Abstract:When an insulating material is subjected to electron irradiation, it produces a secondary emission the yield of which varies from a few percent to very high values (up to 24 per incoming electron) depending on the material and the experimental conditions. If the secondary electron emission yield is less than one, a net negative charge remains trapped in the sample. In this case, the study of the electric charges trapping properties of the material becomes possible. This article describes how it is possible to use a secondary electron microscope (SEM) as a device to perform such a study. In Sec. II, the effect of a net negative trapped charge resulting (from the injection of typically 50 pC) on the imaging process of the SEM has been described. It has been shown that when the trapped charge is high enough, it acts as a mirror reflecting the incoming electron beam which is deflected somewhere in the vacuum chamber of the microscope. A global qualitative description of the image displayed on the screen is first presented. Then electron trajectories are quantitatively studied by using the Rutherford scattering cross section in the case of a point charge. When the charge is extended, a numeric simulation has been done in order to predict the validity range of the previous model. Once the trajectories have been calculated, the connection between the remarkable elements of the image and the quantity of trapped charges has been established. Moreover, this technique allows one to study the lateral dimension of the trapped charge zone and to measure the surface potential. In Sec. III, the discussion is first focused on some precautions to be taken concerning the sample preparation before the experiment is performed. It has been shown that surface defects due either to contamination layers or machining change the trapping properties of single-crystals ceramics such as MgO and Al2O3. A cleaning procedure is proposed that consists of annealing the sample at 1500 °C for 4 h in order to heal the crystalline defects and a heating at 400 °C in the vacuum chamber of the SEM to remove the contamination layers. Finally, the effect of the temperature on the trapping properties of pure and chromium doped sapphire has been studied in relation with the chromium concentration. It is shown that temperature behavior of trapping is in relation with the chromium concentration. In the pure sapphire trapping is activated below −16 °C, in 500 ppm rubis it is below −9.5 °C due to isolated chromium atoms, and in the 8000 ppm rubis the critical trapping temperature rises to 3.7 °C due to Cr3+ pairs. The interpretation of the role played by chromium on trapping is based on the experimental study of the fluorescence of chromium atoms and pairs as a function of concentration.

Charge Compensation by In-Situ Heating for Insulating Ceramics in Scanning Electron Microscope.

Atomic Investigation on the Facet‐Dependent Melting of Ceramic Nanostructures Via in Situ Electron Irradiation

Total-Ionizing-Dose Effects on Al/SiO2 Bimorph Electrothermal Microscanners

On OCRA: response to comments by Wang and Wang (2005)

Space charge measurement in a dielectric material after irradiation with a 30 kV electron beam: Application to single-crystals oxide trapping properties

Measurement of electron beam induced sample heating in SEM experiments

Development and application of a high-temperature imaging system for in-situ scanning electron microscope

Measurements of the Secondary Electron Emission of Some Insulators

Development of a microfurnace dedicated to in situ scanning electron microscope observation up to 1300 °C. II. Study of the thermal response of samples

Quantifying Real-Time Sample Temperature Under the Gas Environment in the Transmission Electron Microscope Using a Novel MEMS Heater

Lymphohistiocytosis: A multi‐factorial syndrome of macrophagic activation clinico‐pathological study of 38 cases

Study of Electrical Conduction Mechanisms of CaCu3Ti4O12–MgAl2O4 Composite Ceramics with NTC Effect Via In-Situ XPS and Complex Impedance Analysis

Effect of Deposited Charge on Vacuum DC Surface Flashover Under Electron Beam Irradiation

Elimination of the charge effect on zirconia coatings using a focused ion beam for characterization of the three-dimensional microstructure

X-ray Photoelectron Spectroscopy Analysis of Scandia-Ceria-Stabilized Zirconia Composites with Different Transport Properties

Evaluating the performance of ionic liquid coatings for mitigation of spacecraft surface charges

Nonlinear change of ion-induced secondary electron emission in the κ-Al2O3 surface charging from first-principle modelling

Measuring coefficient of thermal expansion of materials of micrometre size using SEM/FIB microscope with in situ MEMS heating stage

Investigation of the Inner Microstructure of Composite Materials during their Densification by Scanning Electron Microscopy – LSM:YSZ Electrode Case Study

Design and Application of Variable Temperature Environmental Capsule for Scanning Electron Microscopy in Gases and Liquids at Ambient Conditions

In situ transmission-electron-microscopy investigation of melting in submicron Al-Si alloy particles under electron-beam irradiation