Abstract:When an insulating material is subjected to electron irradiation, it produces a secondary emission the yield of which varies from a few percent to very high values (up to 24 per incoming electron) depending on the material and the experimental conditions. If the secondary electron emission yield is less than one, a net negative charge remains trapped in the sample. In this case, the study of the electric charges trapping properties of the material becomes possible. This article describes how it is possible to use a secondary electron microscope (SEM) as a device to perform such a study. In Sec. II, the effect of a net negative trapped charge resulting (from the injection of typically 50 pC) on the imaging process of the SEM has been described. It has been shown that when the trapped charge is high enough, it acts as a mirror reflecting the incoming electron beam which is deflected somewhere in the vacuum chamber of the microscope. A global qualitative description of the image displayed on the screen is first presented. Then electron trajectories are quantitatively studied by using the Rutherford scattering cross section in the case of a point charge. When the charge is extended, a numeric simulation has been done in order to predict the validity range of the previous model. Once the trajectories have been calculated, the connection between the remarkable elements of the image and the quantity of trapped charges has been established. Moreover, this technique allows one to study the lateral dimension of the trapped charge zone and to measure the surface potential. In Sec. III, the discussion is first focused on some precautions to be taken concerning the sample preparation before the experiment is performed. It has been shown that surface defects due either to contamination layers or machining change the trapping properties of single-crystals ceramics such as MgO and Al2O3. A cleaning procedure is proposed that consists of annealing the sample at 1500 °C for 4 h in order to heal the crystalline defects and a heating at 400 °C in the vacuum chamber of the SEM to remove the contamination layers. Finally, the effect of the temperature on the trapping properties of pure and chromium doped sapphire has been studied in relation with the chromium concentration. It is shown that temperature behavior of trapping is in relation with the chromium concentration. In the pure sapphire trapping is activated below −16 °C, in 500 ppm rubis it is below −9.5 °C due to isolated chromium atoms, and in the 8000 ppm rubis the critical trapping temperature rises to 3.7 °C due to Cr3+ pairs. The interpretation of the role played by chromium on trapping is based on the experimental study of the fluorescence of chromium atoms and pairs as a function of concentration.

Measurements of the Secondary Electron Emission of Some Insulators

Secondary Electron Emission Yield Measurement of Dielectric Materials for Satellite Antenna

Total Electron Emission Yield Measurement of Insulator by A Scanning Small Detector

Study of Characteristic for Secondary Electron Emission of Dielectric with Different Surface Chargings

Measurement of Secondary Electron Energy Spectra of Polymethyl Methacrylate

Secondary Electron Emission Measurements of Dielectric Window Materials

Total Electron Emission Yield of Solar Cell Coverglass and Optical Solar Reflector

Measurements of the Secondary Electron Emission from Rare Gases at 4.2K

Measurement of True Secondary Electron Emission Yields of Kapton

Numerical Study on Effects of Secondary Electrons Generated by Temp Ii Accelerator

Analytical Model of Dynamic Secondary Electron Emission of Insulators under Electron Irradiation

Measurement of electron beam induced sample heating in SEM experiments

Secondary electron emission of TiN-coated alumina ceramics

CHARACTER AND MEASUREMENTS OF SECONDARY ELECTRON EMISSION COEFFICIENTS FOR ALUMINA CERAMICS

Research on the secondary electron yield of TiZrV-Pd thin film coatings

Space charge measurement in a dielectric material after irradiation with a 30 kV electron beam: Application to single-crystals oxide trapping properties

Measurement of Total Electron Emission Yield of Insulators Based on Self-Terminating Charge Neutralization

A New Method for Measuring Total Electron Emission Yield of Insulators.

Note: A simple charge neutralization method for measuring the secondary electron yield of insulators.

New experimental methodology for determining the second crossover energy in insulators under stationary e-irradiation in a SEM

Device for measuring secondary electron emission yield of insulator