Abstract:(Zr62Cu15.4Ni12.6) (x = 6–12) in situ glassy composites containing uniformly distributed Ta-rich particles were prepared by arc-melting and copper mould casting. The results show that addition of 6–10 at.% Ta to Zr62Cu15.4Ni12.6Al10 results in dissolution of 2.4 to 4.6 at.% Ta in the glassy matrix, which promotes glass-forming ability, and the remaining Ta precipitates out as body-centered cubic (BCC) Ta-rich particles dispersed on the glassy matrix. The critical diameters for the composites with 6, 8, and 10 at.% Ta are 7, 7, and 6 mm, respectively. At 12 at.% Ta addition, the glass-forming ability is dramatically reduced because of the precipitation of secondary dendritic Ta-rich particles and other nanocrystallites from melts during copper mould casting. Also, owing to the solid-liquid reaction during induction heating, some Ta-rich particles formed in the master alloys will redissolve into the glassy matrix, resulting in a smaller volume fraction of Ta-rich particles in the as-cast glassy rods than that of the corresponding ingots. The glassy matrix composites exhibit enhanced plastic strain of about 7.5 to 22.5% at room temperature. The optimum Ta content in the glassy alloys is determined to be 10 at.%, which corresponds to the highest ultimate stress of 2220 MPa and the largest plastic strain of 22.5%. The plastic strain increases with increasing volume fraction of in situ BCC Ta-rich particles. This is apparently ascribed to the impedance of Ta-rich particles to shear bands. Ta-rich particles seed the initiation of multiple shear bands and block the shear band propagation, leading to intensive multiplication and bifurcation of shear bands.

The effect of Ti, Nb, and Ta additions to ZrAlCu metallic glass on the crystallization and formation of the icosahedral phase

On the atomic structure of Zr–Ni and Zr–Ni–Al metallic glasses

Effects of Small Amount Ta on the Characteristics of the Zr-Al-Ni-Cu-Ta Bulk Metallic Glass

Effects of Alloying Elements on Crystallization Kinetics of Ti–Zr–Be Bulk Metallic Glass

Cu-alloying Effect on Crystallization Kinetics of Ti41Zr25Be28Fe6 Bulk Metallic Glass

Formation, Thermal Stability and Mechanical Properties of Zr-Nb-Cu-Ni-Al Bulk Metallic Glasses

Effect of Ti addition on properties of Zr54Al10.2Ni9.4Cu26.4 glass forming alloy

Formation of Ni–Nb–Zr–X (X = Ti, Ta, Fe, Cu, Co) Bulk Metallic Glasses

Effect of Nucleating Agents on Structure and Crystallization Behavior of High-aluminum Glass-ceramics System

The effect of minor alloying on the glass forming ability and crystallization reaction of Ti32.8Zr30.2Cu9M5.3Be22.7 (M=Fe, Co, and Ni) bulk metallic glass

Crystallization Path and Non-Isothermal Kinetics of the Zr59.5Cu14.4Ni11.6Al9.7Nb4.8 Metallic Glass under Different Heating Rates

Structure and properties of Zr–Ta–Cu–Ni–Al bulk metallic glasses and metallic glass matrix composites

Glassy and Icosahedral Phases in Rapidly Solidified Ti–Zr–Hf–(Fe, Co or Ni) Alloys

Thermal Stability and Mechanical Properties of Bulk Glassy Cu-Zr-Ti-(Nb, Ta) Alloys

Zr-Cu-Ni-Al-Ta Glassy Matrix Composites with Enhanced Plasticity

Effects of minor addition of Al and Ag elements on the atomic structure and mechanical property of ZrCu-based metallic glasses

Influence of Substitution of Cu by Ni on the Crystallization Kinetics of TiZrHfBeCu High Entropy Bulk Metallic Glass

Microstructure and crystallization in Cu50Zr45Al5 metallic glass

Crystallization and mechanical behavior of (Hf, Zr)–Ti–Cu–Ni–Al metallic glasses

Glass-Forming Ability and Thermal Properties of Al70Fe12.5V12.5X5(X = Zr, Nb, Ni) Amorphous Alloys via Minor Alloying Additions

Improving the glass-forming ability and plasticity of a TiCu-based bulk metallic glass composite by minor Ta doping