Abstract:Negative temperature coefficient (NTC) thermistor materials based on (LaMn 0.5 Co 0.5 O 3 ) x –(Ni 0.66 Mn 2.34 O 4 ) 1−x (0 ≤ x ≤ 0.5) composite ceramics, are fabricated by the conventional solid-state reaction method. The crystal structure, surface morphology and electrical properties of the composite ceramics are investigated and characterized by X-ray powders diffraction (XRD), scanning electron microscope (SEM), and Agilent digital multimeter, respectively. XRD results show that main phases of as-sintered ceramics are a cubic spinel structure Ni 0.66 Mn 2.34 O 4 phase and a rhombohedral perovskite structure LaMn 0.5 Co 0.5 O 3 phase. SEM images indicate that the grain size of the composite ceramics decreases with increasing the low-resistivity perovskite phase. The ρ 25 and B value of the composite ceramics decreases with increasing x, and the B is still reasonably high in the range of 4000–3500 K when x ≤ 0.2. Meanwhile, the introduction of the perovskite phase leads to a decrease in the resistance drift, which the ΔR/R 0 is relatively low (0.26–1.8 %) after annealing at 125 °C for 600 h in air atmosphere. These findings exhibit that (LaMn 0.5 Co 0.5 O 3 ) x –(Ni 0.66 Mn 2.34 O 4 ) 1−x (0 ≤ x ≤ 0.5) composite ceramics have a higher electrical stability in comparison with Ni 0.66 Mn 2.34 O 4 ceramics, are helpful for meeting demands for obtaining better stability and performance of NTC composites ceramics.

Tantalum nitride/copper nanocomposite with zero temperature coefficient of resistance

Fabrication of Ta–Si–N/Ag nanocomposite thin films with near-zero temperature coefficient of resistance

Tunable Temperature Coefficient of Resistivity in C- and Co-doped CuNMn3

Tantalum Nitride Thin Film with a Nearly Zero Temperature Coefficient of Resistance Synthesized by Magnetron Co-Sputtering

Design, Fabrication and Characterization of Porous Ti-Rich Ti-Ni Alloy Based Composites with Near-Zero Thermal Expansion Behavior

Spinel-structured Ni-free ZnCuMnO (0.1 ≤ ≤ 0.5) thermistors of negative temperature coefficient

Spinel-structured Ni-free Zn 0.9 Cu x Mn 2.1- x O 4 (0.1 ≤ x ≤ 0.5) thermistors of negative temperature coefficient

Near-Zero Thermal Expansion and High Thermal Conductivity from Ambient to Cryogenic Temperatures in Hf0.87ta0.13fe2cux

Enhancing the Thermoelectric Performance of Cu–Ni Alloys by Introducing Carbon Nanotubes

Preparation and Characterization of Negative Temperature Coefficient (ni,mn) 3 O 4 –la(mn,ni)o 3 Composite

Tuning the Electronic Properties in TaNx/Ag Nanocomposite Thin Films

N-doped Graphene-Based Copper Nanocomposite with Ultralow Electrical Resistivity and High Thermal Conductivity.

Sintering Temperature and Impedance Analysis of Mn0.9co1.2ni0.27mg0.15al0.03fe0.45o4 Ntc Ceramic Prepared by W/O Microemulsion Method

Design of negative/nearly zero thermal expansion behavior over a wide temperature range by multi-phase composite

Cold-sintered V2O5-PEDOT:PSS Nanocomposites for Negative Temperature Coefficient Materials

NTC thermo-sensitive ceramics with low B value and high resistance at low temperature in Li-doped Mn0.6Ni0.9Co1.5O4 system

Design for High-Performance Functional Composite Thermistor Materials by Glass/ceramic Composing

Design of Zero Thermal Expansion and High Thermal Conductivity in Machinable Xlfcs/cu Metal Matrix Composites

Preparation and characterization of LaMn 0.5 Co 0.5 O 3 –Ni 0.66 Mn 2.34 O 4 composite NTC ceramics

Enhanced Thermoelectric Properties of Nano-Sic Dispersed NaCo2O4 Composites

Zero thermal expansion, high specific thermal conductivity, and good machinability of Cu2P2O7/2024Al composite