Abstract:This study reports the structural evolution of high-entropy alloys from elemental materials to amorphous phases during mechanical alloying, and further, to equilibrium phases during subsequent thermal annealing. Four alloys from quaternary Cu0.5NiAlCo to septenary Cu0.5NiAlCoCrFeTi were analyzed. Microstructure examinations reveal that during mechanical alloying, Cu and Ni first formed a solid solution, and then other elements gradually dissolved into the solid solution which was finally transformed into amorphous structures after prolonged milling. During thermal annealing, recovery of the amorphous powders begins at 100°C, crystallization occurs at 250–280°C, and precipitation and grain growth of equilibrium phases occur at higher temperatures. The glass transition temperature usually observed in bulk amorphous alloys was not observed in the present amorphous phases. These structural evolution reveal three physical significances for high-entropy alloys: (1) the annealed state of amorphous powders produces simple equilibrium solid solution phases instead of complex phases, confirming the high-entropy effect; (2) amorphization caused by mechanical milling still meets the minimum criterion for amorphization based on topological instability proposed by Egami; and (3) the nonexistence of a glass transition temperature suggests that Inoue's rules for bulk amorphous alloys are still crucial for the existence of glass transition for a high-entropy amorphous alloy.

Formation of Zr50Al15-xNi10Cu25Yx Amorphous Alloys from Low Purity Materials by Mechanical Alloying

Glass-Forming Ability and Thermal Properties of Al70Fe12.5V12.5X5(X = Zr, Nb, Ni) Amorphous Alloys via Minor Alloying Additions

Study on isothermal crystallization kinetics of Zr55.7Cu22.4Ni7.2Al14.7 bulk amorphous alloy

Synthesis of High-Thermally Stable Ni60Nb13.3Zr13.3Ti13.3 Amorphous Alloy by Mechanical Alloying

Structural Properties and Thermal Stability of Glassy (Zr<sub>.65</sub>Al<sub>.075</sub>Cu<sub>.175</sub>Ni<sub>.1</sub>)<sub>100-x</sub>Fe<sub>x</sub> (x≤20) Alloys Prepared by Mechanical Alloying

Amorphization in the AlC System by Mechanical Alloying

Bulk Nanostructure Formation Directly From The Multicomponent Alloy Melt

Structural Properties and Thermal Stability of Glassy (Zr.65al.075cu.175ni.1)100-Xfex (x≤20) Alloys Prepared by Mechanical Alloying

Fabrication of nanocrystalline supersaturated W–Al alloys with enhanced thermal stability and high sinterability

Nano-sized Amorphous Cu–Zr Alloy Particles Prepared by Mechanochemical Reaction

Metallographic Analysis of Cu–Zr–Al Bulk Amorphous Alloys with Yttrium Addition

Insights into the structure sustainable evolution and crystallization kinetics of amorphous Mg60Ni30La10 alloy

On the Preparation of Amorphous Mg–Ni Alloys by Mechanical Alloying

Microstructure and elevated-temperature mechanical properties of refractory AlMo0.5NbTa0.5TiZr High Entropy Alloy fabricated by powder metallurgy

Structure of the amorphous, massive-metallic-glass forming Ni 25 Zr 60 Al 15 alloy from molecular dynamics simulations

Influence of niobium and yttrium on plastic deformation energy and plasticity of Ti-based amorphous alloys

Microstructure and Magnetic Properties of Mechanically Alloyed FeSiBAlNi (nb) High Entropy Alloys

Amorphous Alloys Formed by Ion Mixing or Solid-State Reaction in Immiscible Y-Refractory Metal Systems and Their Elastic Properties

Preparation of amorphous Fe-Zr alloys by mechanical alloying and melt spinning methods

Experimental investigation of the effects of cooling with liquid nitrogen and air on the microstructure and mechanical properties of Zr50Cu34Al8Ag8 amorphous alloy

Structural evolution during mechanical milling and subsequent annealing of Cu–Ni–Al–Co–Cr–Fe–Ti alloys