Abstract:Amorphous 2Mg–Fe+xwt.% Ni alloys were synthesized by mechanical alloying of Mg and Fe elemental powders. Two kinds of ball-milling atmospheres, namely, (1) under argon and (2) first under argon and then in tetrahydrofuran (THF), were examined in this study. The effects of the Ni addition and ball-milling time and atmosphere on the microstructure and electrochemical properties of the prepared alloys have been investigated systematically. The results show that the ball-milled (2Mg–Fe) nickel-free mixture still maintains Mg and Fe elemental phases, and its discharge capacity is only 19.2mAhg−1. The Ni powder addition is advantageous for the formation of Mg–Fe amorphous structure and for the improvement of the electrochemical properties of the alloys. For the alloys milled under argon, with the Ni content x increasing, the discharge capacity of the alloys increases first and then decreases, and reaches a maximum value of 455.3mAhg−1 as x=100. With the milling-time extending, the discharge capacity of the alloy increases first and then decreases too. For the alloys milled under argon and then in THF, the alloys exhibit higher degree of amorphorization, bigger specific surface area and more active surfaces, and thus have better electrochemical properties than those milled under argon. With the Ni increasing, the discharge capacity increases from 249.7mAhg−1 (x=50) to 565.2mAhg−1 (x=150) and then decreases to 497.9mAhg−1 (x=200), and the exchange current density I0 increases from 104.8mAg−1 (x=50) to 251.1mAg−1 (x=200), which is consistent with the variation of the HRD of the alloy electrodes in the investigation range.

On the Preparation of Amorphous Mg–Ni Alloys by Mechanical Alloying

An electrochemical investigation of mechanical alloying of MgNi-based hydrogen storage alloys

Electrochemical properties of amorphous Mg–Fe alloys mixed with Ni prepared by ball-milling

Formation of MgCNi3 and Mg–Ni Amorphous Mixture by Mechanical Alloying of Mg–Ni–C System

Mechanical Ball Milling Preparation and Electrochemical Hydrogen Storage Properties of Amorphous Mg-Fe Composites

The Electrochemical Evaluation of Ball Milled MgNi-based Hydrogen Storage Alloys

Microstructures and electrochemical hydrogen storage properties of novel Mg–Al–Ni amorphous composites

Amorphization and Electrochemical Hydrogen Storage Properties of Mechanically Alloyed Mg–Ni

Microstructure and electrochemical properties of amorphous composites of ball-milled Mg2Ni0.95Sn0.05 + x wt% Ni

Microstructure and electrochemical properties of amorphous Mg-Fe-Ni hydrogen storage electrode material

Solid state reaction and formation of nano-phase composite hydrogen storage alloy by mechanical alloying of MmNi 3.5 (CoMnAl) 1.5 and Mg

Synthesis of High-Thermally Stable Ni60Nb13.3Zr13.3Ti13.3 Amorphous Alloy by Mechanical Alloying

Preparations and Electrochemical Properties of Amorphous Ti-Al Alloys

Studies on thermodynamic and kinetic and phase evolution of W-Ni-Fe powder during mechanical alloying

Study of the effect of mechanical alloying on the structure of Ni-Mn-Sn Heusler alloy

Mechanical alloying induced solid state reaction and formation of nano-phase composite hydrogen storage alloys in MmNi5-x(Co, Al, Mn)x/Mg system

Formation of Crystalline and Amorphous Solid Solutions of W–Ni–Fe Powder During Mechanical Alloying

Fabrication of Amorphous Ti63.7Nb21.3Zr4.5Ta1.5Fe9 Powder by Mechanical Alloying

Research on the Structures and Discharge Capacities of Mg–Ni Alloy with Different Ni Contents Synthesized by High-Energy Ball Milling

Magnetic and Microstructural Properties of Nanostructured/Amorphous NiTi Prepared by Mechanical Alloying

Preparation of Mg2Ni Hydrogen Storage Alloy Materials by High Energy Ball Milling