Abstract:In this study, structural, morphological, thermal and magnetic properties of amorphous-nanocrystalline Fe 70 Cr 10 Nb 10 B 10 (at.%) alloy are discussed. The formation and evaluation of amorphous-nanocrystalline structures of the alloy were followed by XRD, SEM-EDX, TEM, DTA, and VSM techniques. After 50 h of milling Cr, Nb, and B were completely dissolved into the Fe lattice forming 82% of the amorphous phase of the alloy. A gradual dissolution of the alloying elements also increased the lattice parameters concurrently. The lattice parameters reached a maximum value of 2.908 Å after 20 h of milling and then leveled off to a value of 2.891 Å at the end of 50 h of milling. Based on the XRD data, crystallite size and lattice strain of the alloy were calculated as 3.2 nm and 3.34% respectively. TEM analyses revealed that the alloy particulates comprised needle-shaped nanoparticles of an average size of 21 nm. The room temperature magnetic hysteresis loops showed that the increased duration of milling decreased the saturation magnetization from 91 to 24 emu/g. This was mainly due to the upsurge on the amorphous phase content in the alloy as the milling progressed. The increase in amorphous phase content and the subsequent reduction of the saturation magnetization were due to the inter-diffusion of the non-ferromagnetic Cr and B atoms into the Fe lattice. Thermal studies revealed that around 350 °C the amorphous phase of the alloy began crystallizing. The magnetic saturation of the heat-treated alloy also increased with the growth in the crystalline phases. The 50 h milled sample annealed at 700 °C was found to have the highest magnetic anisotropy as observed from the temperature-dependent zero-field cooled and field cooled magnetization measurements. The high-pressure X-ray diffraction measurements revealed that the amorphous state of the alloy remained stable up to 11.3 MPa. It also revealed the structural similarities of the Fe 70 Cr 10 Nb 10 B 10 alloy with those of the Fe 70 M 10 B 20 (M = Nb and Cr) types. For all practical purposes, the microstructural stability under high compressive pressure represents the consolidation properties of the nanostructured magnetic materials since both pressure and temperature-induced phase transformations are the primary controlling factors for the specific magnetization properties of the alloy.

Synthesis of High-Thermally Stable Ni60Nb13.3Zr13.3Ti13.3 Amorphous Alloy by Mechanical Alloying

Investigation of a Hot-Pressed Nb–Ti–Al Alloy: Mechanical Alloying, Microstructure and Mechanical Property

Synthesis and characterization of amorphous-nanocrystalline Fe70Cr10Nb10B10 powders by mechanical alloying

On the Preparation of Amorphous Mg–Ni Alloys by Mechanical Alloying

Amorphization in the AlC System by Mechanical Alloying

Microstructural evolution and thermal stability in a nanocrystalline lightweight TiAlV0.5CrMo refractory high-entropy alloy synthesized by mechanical alloying

Nanocrystalline/Amorphous Tuning of Al–Fe–Nb (Mn) Alloy Powders Produced via High-Energy Ball Milling

Magnetic and Microstructural Properties of Nanostructured/Amorphous NiTi Prepared by Mechanical Alloying

Study on isothermal crystallization kinetics of Zr55.7Cu22.4Ni7.2Al14.7 bulk amorphous alloy

PHASE TRANSFORMATION IN ANNEALED MECHANICAL ALLOYING Nd-11Fe-Ti ALLOY AND ANNEALED MECHANICAL MILLING NdFe11Ti COMPOUND

Nanostructured Al–Ti–Fe–Mn–Ni High-Entropy Alloy by Mechanical Alloying: Synthesis and Characterization

Study on mechanical alloying behavior and thermal stability of HfMoNbTaTi refractory high-entropy alloy

Study of the effect of mechanical alloying on the structure of Ni-Mn-Sn Heusler alloy

Insights into the structure sustainable evolution and crystallization kinetics of amorphous Mg60Ni30La10 alloy

Thermo-mechanical behavior of hypoeutectic Ni-Y-Zr alloys

Structural evolution during mechanical milling and subsequent annealing of Cu–Ni–Al–Co–Cr–Fe–Ti alloys

Microstructure and elevated-temperature mechanical properties of refractory AlMo0.5NbTa0.5TiZr High Entropy Alloy fabricated by powder metallurgy

Evaluation of the Microstructure and Magnetic Properties of Amorphous Co62Nb32B6 Alloy Produced by Mechanical Alloying

Crystallization behavior and corrosion resistance of Al86Ni10Zr4 amorphous alloy under different annealing treatment conditions

Phase Transformation and Morphology Evolution of Ti50Cu25Ni20Sn5 during Mechanical Milling

Structural and thermal properties of the Fe-based alloys prepared by mechanical milling