Abstract:In this paper, Zr50Cu34Al8Ag8 amorphous alloy bars were prepared by copper-mold suction casting. The compressive mechanical properties of the as-cast samples and the alloy samples isothermally annealed for different times were tested by a universal testing machine, and the hardness values of the samples were measured by an automatic microhardness measurement system. The microstructure and thermodynamic properties of the alloy samples were analyzed by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and differential scanning calorimetry. The experimental results show that both annealing temperature and annealing time have significant effects on the microstructure and properties of the amorphous alloys. At an isothermal annealing temperature of 430 °C, the incubation time was 100.6 min, which decreased to 5.4 min when the temperature was increased to 460 °C. With prolonged isothermal annealing time, the width of the supercooled liquid region of the alloy samples became narrower and the stability decreased. After isothermal annealing at 440 °C for 20 min, the volume fraction of the crystalline phase in the alloy sample reached 45.2%, and the hardness of the alloy sample reached the maximum value of 526.5 HV. The compressive mechanical properties of the as-cast samples were the best with a compressive strength and ultimate strain of 1856.8 MPa and 3.57%, respectively. When increasing the isothermal annealing time, the compressive mechanical properties of the alloy samples decreased sharply, and the fracture mode changed from shear fracture to brittle fracture. The precipitation of hexagonal Al2Zr and tetragonal AgZr phases inside the alloy samples was the main reason for the decrease in the compressive mechanical properties and the increase in the hardness.

Crystallization behavior and corrosion resistance of Al86Ni10Zr4 amorphous alloy under different annealing treatment conditions

MICROSTRUCTURE OF AS-MELT SPUN Al-Cu-Mg-Fe-Ni ALLOY AND ITS VARIATION IN CONTINUOUS HEAT TREATMENT

Atomic-scale study on the precipitation behavior of an Al-Zn-Mg-Cu alloy during isochronal aging

The Crystallization Kinetics Study of Finemet-Co Amorphous Alloys

Study on isothermal crystallization kinetics of Zr55.7Cu22.4Ni7.2Al14.7 bulk amorphous alloy

Nanocrystallization Kinetics of Amorphous Fe73.5Cu1Nb3−xMoxSi13.5B9 (x=1, 2, 3) Alloys

Structure and phase transformations of amorphous-nanocrystalline Al-based alloy

Thermal stability and corrosion behavior of a novel Zr22.5Ti22.5Hf22.5Ni22.5Ta10 high-entropy amorphous alloy

Crystallization Kinetics of Co-Finemet Amorphous Alloys and Magnetic Properties of Nanocrystalline Powder Cores

Excellent Corrosion and Wear Resistance of Amorphous and Crystalline ZrCoAl Alloys

An ab initio simulation and experimental studies of the glass-forming ability and properties of Al86Ni(14-x)Zrx (x = 1∼7) alloys

Corrosion behaviors of amorphous and nanocrystalline Fe-based alloys in NaCl solution

Sem Study of Quasi-Crystallized Zr65cu12.5ni10al7.5ag5 Amorphous Alloy at Initial Stage

Atomic level simulation of amorphous/nanocrystalline transition behavior in the Fe based amorphous alloys

Effect of isothermal annealing on microstructure evolution and mechanical properties of Zr50Cu34Al8Ag8 amorphous alloy

Unexpected thermal stability of dual-phase amorphous-nanocrystalline Al0.74Mo0.26 alloy film prepared by annealing-induced crystallization

Study on structure relaxation of Zr55Cu30Al10Ni5 bulk amorphous alloy

The effect of annealing temperatures on the phase constitutes, thermal properties and corrosion behaviors of Ti-Ni-Zr-Cu high entropy alloy thin ribbons

An investigation into the effect of isothermal annealing on the structure (XRD), microstructure (SEM, TEM) and magnetic properties of amorphous ribbons and bulk amorphous plates

Crystallization kinetics of Cu64Zr36 amorphous alloy

Insights into the structure sustainable evolution and crystallization kinetics of amorphous Mg60Ni30La10 alloy