Abstract:Amorphous 2Mg–Fe+xwt.% Ni alloys were synthesized by mechanical alloying of Mg and Fe elemental powders. Two kinds of ball-milling atmospheres, namely, (1) under argon and (2) first under argon and then in tetrahydrofuran (THF), were examined in this study. The effects of the Ni addition and ball-milling time and atmosphere on the microstructure and electrochemical properties of the prepared alloys have been investigated systematically. The results show that the ball-milled (2Mg–Fe) nickel-free mixture still maintains Mg and Fe elemental phases, and its discharge capacity is only 19.2mAhg−1. The Ni powder addition is advantageous for the formation of Mg–Fe amorphous structure and for the improvement of the electrochemical properties of the alloys. For the alloys milled under argon, with the Ni content x increasing, the discharge capacity of the alloys increases first and then decreases, and reaches a maximum value of 455.3mAhg−1 as x=100. With the milling-time extending, the discharge capacity of the alloy increases first and then decreases too. For the alloys milled under argon and then in THF, the alloys exhibit higher degree of amorphorization, bigger specific surface area and more active surfaces, and thus have better electrochemical properties than those milled under argon. With the Ni increasing, the discharge capacity increases from 249.7mAhg−1 (x=50) to 565.2mAhg−1 (x=150) and then decreases to 497.9mAhg−1 (x=200), and the exchange current density I0 increases from 104.8mAg−1 (x=50) to 251.1mAg−1 (x=200), which is consistent with the variation of the HRD of the alloy electrodes in the investigation range.

Preparations and Electrochemical Properties of Amorphous Ti-Al Alloys

Electrochemical properties of amorphous Mg–Fe alloys mixed with Ni prepared by ball-milling

Electrochemical Performance of the Ball-Milled La2Mg14−xTixNi3 Alloys with Ni Powders (x=1 and 2)

Microstructure and electrochemical properties of amorphous composites of ball-milled Mg2Ni0.95Sn0.05 + x wt% Ni

Microstructures and electrochemical hydrogen storage properties of novel Mg–Al–Ni amorphous composites

Influence of Ball-Milling with Cu Powder on Electrochemical Properties of V-based Solid Solution Type Hydrogen Storage Alloys

Microstructure and electrochemical properties of amorphous Mg-Fe-Ni hydrogen storage electrode material

An electrochemical investigation of mechanical alloying of MgNi-based hydrogen storage alloys

The Electrochemical Evaluation of Ball Milled MgNi-based Hydrogen Storage Alloys

The effect of temperature on the electrode properties of the directly prepared Ti3Ni2 alloy

Influence of Ball-milling with Ni Powder on the Phase Structure and Electrochemical Hydrogen Storage Properties of Mg17Al12 Alloy

Effects of Surface Modification on the Electrode Behavior of Ball-Milled La2Mg17 + 200 Wt% Ni Composite in Alkaline Solution

The Effect of Ni Content on the Phase Structures and Electrochemical Properties of V2.1TiNix (x=0.1–0.9) Hydrogen Storage Alloys

V 2.1 TiNi 0.4 Zr 0.06 Cu 0.03 M 0.10 (M=Cr, Co, Fe, Nb, Ta)储氢合金的微结构及电化学性能

The Effects of Titanium on the Phase Structure and Charge/Discharge Performance of Ml(Nicomnti)(5) Alloy

Microstructure and Electrochemical Properties of V_(2.1)TiNi_(0.4)Zr_(0.06)Cu_(0.03)M_(0.10)(M=Cr, Co, Fe, Nb, Ta) Hydrogen Storage Alloys

Effects of Surface Modification on the Electrode Behavior of Amorphous CeMg12 Alloys

The Structure and Electrochemical Properties of Ball-Milled Ti0.9Zr0.2Mn1.6Ni0.2V0.2 Alloys

Influence of the material processing on the electrochemical properties of cobalt-free Ml(NiMnAlFe)5 alloy

The phase structures and electrochemical properties of TiV2.1Nix(x=0.2 similar to 0.6) hydrogen storage alloys

The Mechanical Properties of Intermetallic Ni50−xTi50Alx Alloys (X=6,7,8,9)