Abstract:Aiming at enhancing the electrochemical characteristic of RE-Mg-based composite, the partial substituting La with Ce experiment in the composites was conducted, and the surface modification treatment of the alloys was performed by mechanical coating Ni. By means of mechanical trituration, The La 10-x Ce x Mg 80 Ni 5 (x = 0–2) + y wt% Ni (y = 50–200) compound materials which have the structures of nanocrystalline and amorphous were synthesized. In order to make sense of the principle action of Ce and Ni elements in structural and electrochemical properties of the material, some deep research were carried out. According to the final results, the as-milled composites have the electrochemical hydrogen absorption and hydrogen desorption abilities at room temperature. Having no use for activation, the as-milled composites can reach the maximum discharge capacities when the first cycling was carried out. With the Ni value x changed from 50 to 200, the discharge capacity was varied from 70.5 mAh/g to 902.1 mAh/g; moreover, the capacity retention rate at 20th cycle (S 20 ) and high rate dischargeability (HRD) of the (x = 0) composite were heightened from 67.2 % to 82.3 %, from 50.6 % to 55.7 % respectively. The composites' (y = 100) discharge capacity has a maximum value 118.5 mAh/g when the Ce value x is 1. The capacity retention rate (S 20 ) is enhanced from 53.3 % to 68.5 % by lifting Ce content from x = 0 to x = 2. what's more, the high-rate discharge ability (HRD), the electrochemical impedance spectrum (EIS), potentiodynamic polarization curves, and potential-step measurements all intimate that substituting La with Ce clearly promotes the composites' electrochemical kinetic properties, but maximum values emerge only when the x value is 1.

Effects of Surface Modification on the Electrode Behavior of Amorphous CeMg12 Alloys

Effects of Surface Coating on the Electrochemical Properties of Amorphous CeMg12 Composite

Electrochemical Properties of Cemg12+X%Ni Composites (X=0 Similar to 200) Prepared by Ball-Milling

Electrochemical Properties of CeMg12＋x% Ni Composites （x=0～200） Prepared by Ball-Milling

Electrochemical Properties of Cemg11ni+X% Ni Composites (X=0, 50, 100 and 200) Prepared by Ball-Milling

Effects of Surface Modification on the Electrode Behavior of Ball-Milled La2Mg17 + 200 Wt% Ni Composite in Alkaline Solution

Microstructure and Electrochemical Properties of Mechanically Ground Ce2Mg17 + X Wt.% Ni (x = 0, 50, 100, 200) Composites

Electrochemical hydrogen storage of ball-milled CeMg12 and PrMg12 alloys with Ni powders

Effect of ball-milling time on the electrochemical performance of ball-milled LaMg11Ni+200wt% Ni composite

Microstructure and electrochemical properties of amorphous composites of ball-milled Mg2Ni0.95Sn0.05 + x wt% Ni

The Electrochemical Evaluation of Ball Milled MgNi-based Hydrogen Storage Alloys

Effect of Ce replacing La on the electrochemical performance of amorphous grain boundaries Mg-Ni-based materials

Electrochemical properties of amorphous Mg–Fe alloys mixed with Ni prepared by ball-milling

Electrochemical Performance of the Ball-Milled La2Mg14−xTixNi3 Alloys with Ni Powders (x=1 and 2)

The electrochemical properties of MgNi– x wt% TiNi 0.56 Co 0.44 ( x = 0, 10, 30, 50) composite alloys

Influence of Ball-milling with Ni Powder on the Phase Structure and Electrochemical Hydrogen Storage Properties of Mg17Al12 Alloy

Electrochemical performance of Si–CeMg12 composites as anode materials for Li-ion batteries

Effect of Surface Modification by Cuxby on Cycle Stability of Mg50ni50 Alloy

Structure and Electrochemical Characteristics of CeMn_(1-x)Al_(1-x)Ni_(2x) (x=0.00,0.25,0.50 and 0.75) Alloys

Electrochemical Characteristics of Amorphous Mgtixni (X=0, 0.1, and 0.2) Hydrogen Storage Alloys

Surface Modification Of Amorphous Mgni Electrodes