Abstract:Polyimide (PI) composite films with enhanced mechanical properties were prepared by incorporating modified fumed silica (FS) particles while preserving their optical and thermal characteristics. The PI matrix was synthesized using a fluorinated diamine, a fluorinated dianhydride, and a rigid biphenyl dianhydride via chemical imidization. Commercially available FS particles, including unmodified FS particles (0-FS) and particles modified with dimethyl (2-FS), trimethyl (3-FS), octyl (8-FS), octamethylcyclotetrasiloxane (D4-FS), and polydimethylsiloxane (PDMS-FS) were used. Scanning electron microscope images and nitrogen adsorption–desorption isotherms revealed well-defined porous structures in the FS particles. The water contact angles on the composite films increased compared to those of the pristine PI films, indicating improved water resistance. The PI/0-FS films exhibited a typical trade-off relationship between tensile modulus and elongation at break, as observed in conventional composites. Owing to the poor compatibility and agglomeration of the PDMS-FS particles, the PI/PDMS-FS composite films exhibited poor mechanical performance and diminished optical characteristics. Although the longer-chained FS particles (8- and D4-FS) improved the tensile modulus of the PI film by up to 12%, a reduction of more than 20% in toughness was observed. The PI composite films containing the methylated FS particles (2- and 3-FS) outperformed 8- and D4-FS in terms of mechanical properties, with PI/3-FS films showing an over 10% increased tensile modulus (from 4.07 to 4.42 GPa) and 15% improved toughness (from 6.97 to 8.04 MJ/m3) at 7 wt. % silica loading. Except for the PI/PDMS-FS composites, all composite film samples exhibited more than 86% transmittance at 550 nm. Regarding thermal properties, the glass transition temperature (Tg) and thermal stability remained stable for most composite films. In addition, PI/3-FS films demonstrated enhanced dimensional stability with lower coefficients of thermal expansion (from 47.3 to 34.5 ppm/°C). Overall, this study highlights the potential of incorporating specific modified FS particles to tailor the mechanical, optical, and thermal properties of PI composite films.

PREPARATION AND STUDY ON STRUCTURE OF THE POLYIMIDE/SILICA HYBRID AND NANOCOMPOSITE FILMS

Preparation and Dielectric Properties of Polyimide/silica Nanocomposite Films Prepared from Sol–gel and Blending Process

Silica/polyimide Hybrids and Their Dielectric Properties. I. Preparation with an Improved Sol–gel Process with Poly(amic Acid) As the Precursor

Preparation and imidization of polyimide composites filled with boron nitride

Comparison of Hybrid Polyimide Films with Silica and Organosilica Obtained Via Sol–gel Process

Synthesis and Characterization of Nanocomposite of Polyimide-Silica Hybrid from Nonaqueous Sol-Gel Process

Microstructure and Properties of Organosoluble Polyimide/silica Hybrid Films

Polyimide/silica/titania Nanohybrids Via a Novel Non-Hydrolytic Sol–gel Route

Properties of Polyimide/Silica Nanohybrids from Silicic Acid Oligomer

Preparation, Morphological and Thermal Stability of Polyimide/Silica Hybrid Material Containing Dye Nbdpa

Synthesis and characterisation of nano‐alumina hybrid polyimide films

Synthesis And Characterization Of Polyimide/Silica Hybrid Waveguide Materials Via Sol-Gel Technique

Novel Polyimide/Silica Nanohybrids from Water Glass

Preparation and Properties of Nanoporous Polyimide Films with Low Dielectric Permittivity

Enhanced Mechanical and Thermal Properties of Polyimide Films Using Hydrophobic Fumed Silica Fillers

Synthesis, structural and morphological characteristics of (P(MA-MPTMS)/SiO2 hybrid nanocomposites

Preparation, characterizations and investigation of properties of new poly(ether-imide) nanocomposite films reinforced with zinc oxide nanoparticles

The Preparation and Properties of Polyimide Films Modified by Octa(aminopropylsilsesquioxane)

Interaction and Microstructure of Polyurethane/Silica Hybrid Films Prepared by Sol-Gel Process

Preparation and Characterization of Polyimide/Fluorinated Silicate Nano-Hybrid Thin Films with Low Refractive Indices

Constructing high‐polarization silica for polyimide‐based nanocomposites with enhanced dielectric permittivity and mechanical performances: Molecular dynamics simulations