Abstract:Combustion synthesis (CS) is a well-known technique for manufacturing intermetallic compounds and intermetallic-matrix composite materials. This research focuses on fabricating NiAl-matrix composites with varying TiC/TiB2 contents as reinforcement, achieved by the combustion synthesis method. The chemical reactions that yield the final NiAl-TiC-TiB2 compounds were interpreted using thermodynamic calculations. The phase analysis and morphology of the composites were investigated using X-ray diffractometry (XRD) and scanning electron microscopy (SEM) characterization techniques, respectively. The findings demonstrate that the NiAl matrix contains evenly distributed TiC-TiB 2 ceramic-based particles, and no oxidation of reactants occurred during the combustion reaction. With an increase in the TiC-TiB 2 reinforcement phases from 0 to 15 Wt. %, the hardness of the NiAl-TiC-TiB 2 product significantly rose from 496 to 1015 Vickers, while the porosity increased from 24% to 39%, attributed to the reduced quantity of melted NiAl available to fill the pores. Examining tribological behavior in synthesized composites involved combining experimental-numerical methods, utilizing sliding wear tests and artificial neural network (ANN) modeling. The wear results revealed decreasing wear rates with reduced loads (from 35 N to 25, and 15 N) and higher TiC/TiB 2 ceramic content. Iron traces at C0 and C10 worn samples were 2.47 and 26.18 Wt. % respectively, which indicates enhanced hardness. The experimental data were used to train and test an artificial neural network (ANN) and statistical analysis revealed a remarkable accuracy of 91% for the ANN model in predicting friction coefficients within SHS-processed composites, as indicated by the R2 value of 0.91 and a MAPE of 6.47.

Improving Wear Resistance of TiNi Matrix Composites Reinforced by Carbon Nanotubes and in Situ TiC

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

Influence of Carbon Contents on the Structure and Tribocorrosion Properties of Tisicn Coatings on Ti6al4v

SYNTHESIS AND THE PERFORMANCE OF CARBON NANOTUBES-(Ni-P) COMPOSITES

Dry Sliding Wear Properties of Annealed Carbon Steels Matrix Composites by Nano‐Sized TiC‐TiB2 Particles

Dry Sliding Wear Properties of Annealed Carbon Steels Matrix Composites by Nanosized TiC‐TiB2 Particles

Optimization of the mechanical properties of CNTs/Cu composite by regulating the size of interfacial TiC

Achieving high strength and superior wear‐resistant properties in TiH2 matrix reinforced with graphene nanoplates

Tuning composition and microstructure by doping Ti and C for enhancing mechanical property and wear resistance of Al0.2Co1.5CrFeNi1.5Ti0.5 high entropy alloy matrix composites

Synergistic optimization of mechanical and tribological properties of TiC modified copper-graphite composites by direct current in-situ sintering

Enhanced properties of titanium matrix composites via in-situ synthesized TiCx and Ti 5 Si 3 with network structure

Microstructure evolution, mechanical properties, and wear behavior of in-situ TiCx/TC4 composites

An Investigation of the Sliding Wear Behavior of Cu-Matrix Composite Reinforced by Carbon Nanotubes

Tribological properties of Ni–P-multi-walled carbon nanotubes electroless composite coating

Fabrication and wear behavior of TiC/TiB 2 -reinforced NiAl intermetallic matrix composites

Study on Microstructure and Mechanical Properties Modification of Cu-Ti3AlC2 Composites by Ni Element

Tribological Application of Carbon Nanotubes in a Metal-Based Composite Coating and Composites

Simultaneous Improvement in Strength and Ductility of TC4 Matrix Composites Reinforced with Ti1400 Alloy and In Situ-Synthesized TiC

Regulating the mechanical properties and electrical conductivity of CNTs/Cu composites by tailoring nano-sized TiC on the surface of intact CNTs

Influence of Ti3C2Tx Addition on the Corrosion Behaviour and Tribological Properties of Electrodeposited Ni-W-Ti3C2Tx Nanocomposite Coatings

Preparation and Characterization of In Situ (TiC-TiB2)/Al-Cu-Mg-Si Composites with High Strength and Wear Resistance