Abstract:For titanium matrix composites (TMCs) with a dual-phase structure, yield strength (YS) is typically governed by the hard α phase rather than the soft β phase in the matrix alloy. Therefore, by controlling the precipitation of nanoscale secondary α phases (α s ) within the β phase, lattice distortion can be induced, leading to dislocation pile-ups at the α s /β phase interface, thereby achieving strengthening of the matrix interface. Herein, TiC/TA19 composites were fabricated using spark plasma sintering, and induced the dispersion and pinning of nanoscale α s phases from the β phase at the α s /β phase interface through multi-pass cumulative rolling, achieving super high strength. In particular, the nanoscale α s phase exhibits two typical Burgers orientation relationships with the β phase, i.e. (0001) α s//(110) β & [11 2− 0] α s//[ 1− 11] β and (0001) α s//(01 1− ) β & [11 2− 0] α s//[ 1− 11] β , respectively. Compared with the yield strength of sintered composites, when the rolling reduction was 75 %, the YS of TiC/TA19 composites increased by 33.7 %, reaching 1368 MPa, and the elongation was 3.6 %, only 0.7 % lower than that of sintered composites (4.3 %). The enhanced strength is mainly attributed to the α s precipitation for α s /β interface strengthening and dislocation strengthening derived from the TiC and nanoscale α s precipitates. The volume fraction of dynamic recrystallization grains in TiC/TA19 composites increased with the rolling reduction, and more pyramidal slip systems were activated to coordinate the plastic deformation of the composites. This study offers a promising route to fabricating superior high-strength TMCs and provides new insights into balancing strength and ductility.

Achieving high strength and superior wear‐resistant properties in TiH2 matrix reinforced with graphene nanoplates

Tuning composition and microstructure by doping Ti and C for enhancing mechanical property and wear resistance of Al0.2Co1.5CrFeNi1.5Ti0.5 high entropy alloy matrix composites

Investigation of microstructure and tribological performances of high-fraction TiC/graphene reinforced self-lubricating Al matrix composites

Tribological Behavior Of Graphene Reinforced 600 Degrees C High Temperature Titanium Alloy Matrix Composite

Fabrication of TiC-graphene dual-reinforced self-lubricating Al matrix hybrid nanocomposites with superior mechanical and tribological properties

In-situ synthesized TiC/Ti-6Al-4V composites by elemental powder mixing and spark plasma sintering: Microstructural evolution and mechanical properties

Microstructure and tribological properties of titanium matrix nanocomposites through powder metallurgy using graphene oxide nanosheets enhanced copper powders and spark plasma sintering

Synergistic effects of TiC and graphene on the microstructure and tribological properties of Al2024 matrix composites

Wear-Resistant TiC Strengthening CoCrNi-Based High-Entropy Alloy Composite

Achieving balanced strength-ductility of heterostructured TiC/graphene nanoplatelets (GNPs) reinforced Al matrix composites by tuning TiC-to-GNPs ratio

Preparation and Characterization of In Situ (TiC-TiB2)/Al-Cu-Mg-Si Composites with High Strength and Wear Resistance

Dry Sliding Wear Properties of Annealed Carbon Steels Matrix Composites by Nano‐Sized TiC‐TiB2 Particles

Densification, Microstructure and Mechanical Performance of TiC/Fe Composites by Spark Plasma Sintering

Dry Sliding Wear Properties of Annealed Carbon Steels Matrix Composites by Nanosized TiC‐TiB2 Particles

Graphene-TiC hybrid reinforced titanium matrix composites with 3D network architecture: Fabrication, microstructure and mechanical properties

Improving Wear Resistance of TiNi Matrix Composites Reinforced by Carbon Nanotubes and in Situ TiC

Microstructure and tribological properties of titanium matrix composites reinforced with in situ synthesized TiC particles

Intergrowth Microstructure and Superior Wear Resistance of (tib + TiC)/Ti64 Hybrid Coatings by Gas Tungsten Arc Cladding

Investigation on Microstructures and Mechanical Behavior of In-Situ Synthesized TiC and TiB Reinforced Ti6Al4V Based Composite

Heterogeneous network structures formed in TiC/TC4/β-Ti composites for enhancing both strength and ductility

Significantly improved strength of the TiC/TA19 composites via interface and dislocation strengthening