Abstract:Abstract Here, numerous oxygen-containing functional groups were grafted onto the surface of CNTs to improve their dispersibility in an electrolyte. The CNTs were characterized by FT-IR, Raman, XPS, FE-SEM, and TEM. The results revealed that the dispersibility of the functionalized CNTs in the composites was better than unfunctionalized CNTs. CNTs/Ni composites were deposited on a copper plate by pulsed electrodeposition and ultrasonic dispersion using an electrolytic bath with CNTs concentrations from 0 to 2 g l −1 . The friction and wear behavior of the composite coatings were assessed using two different methods. In the first method, the coatings were scratched with a progressively higher load from 0–100 N, and the results demonstrate a 10 percent reduction in the coefficient of friction (COF) of the composite compared to pure nickel. The other method involved applying a constant load of 30 N, the COF and microscopic wear mechanism were investigated at different carbon nanotube contents, and the results confirmed that the COF of the composites was gradually reduced with the increase of carbon nanotube mass concentration, and the COF was only 0.343 when the carbon nanotube content was increased to 2 g l −1 . According to the XRD results, increasing the CNTs contents changed the preferred growth orientation. Moreover, the FE-SEM images of the wear surface of the 1 g l −1 CNTs/Ni sample indicated that it had the best wear resistance and showed the smoothest wear trace without apparent cracks. The addition of CNTs enhanced the wear resistance of the nickel matrix due to the superior mechanical strength and lubricating effect of the CNTs. CNTs exposed to the matrix surface reduced the direct contact between the Ni matrix and the friction pair, acted as lubricants, and reduced the wear rate.

Influence of Ti3C2Tx Addition on the Corrosion Behaviour and Tribological Properties of Electrodeposited Ni-W-Ti3C2Tx Nanocomposite Coatings

Influence of the bath pH value on the microstructure and properties of a novel electrodeposited Ni-W-Ti3C2TX composite coating

Influence of Carbon Contents on the Structure and Tribocorrosion Properties of Tisicn Coatings on Ti6al4v

Preparation of Ni-P-Ti3C2Tx-Ce composite coating with enhanced wear resistance and electrochemical corrosion behavior on the surface of low manganese steel

Influence of TiC Addition on Corrosion and Tribocorrosion Resistance of Cr2Ti-NiAl Electrospark Coatings

Enhanced wear resistance of Ni-Mo-TiN composite coating by synergistic effect of tough Ni-Mo matrix and hard TiN particles

Mechanical and Corrosion Resistance Properties of Tio2 Nanoparticles Reinforced Ni Coating by Electrodeposition

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

Corrosion and wear resistance behaviors of electroless Ni–Cu–P–TiN composite coating

Friction and wear behaviors of electrodeposited Ni-P-CNTs composite coatings on Al-alloy substrate

Study on the friction and wear properties of nickel-based-WC-10Ni composite coatings prepared on the surface of TC4 titanium alloy

Study on the Tribology Properties of the Particles/Cu Composite Coatings

Tribological properties of Ni–P-multi-walled carbon nanotubes electroless composite coating

Friction and Wear Behavior of Electroless Ni-Based Cnt Composite Coatings

Deposition and properties of plasma sprayed NiCrCoMo–TiC composite coatings

Preparation and properties of Ni-W-P-TiO2 nanocomposite coatings developed by a sol-enhanced electroplating method

Microstructure and Tribological Properties of WC/Ni-MoS2 Titanium-Based Composite Coating on TC4

Electroless Preparation and Tribological Properties of Ni-P-Carbon Nanotube Composite Coatings under Lubricated Condition

Influences of Mwcnts Concentration on the Friction and Anti-Wear Behavior of Ni-P Coating

Investigation of the microstructure and tribological properties of CNTs/Ni composites prepared by electrodeposition

Tribological Application of Carbon Nanotubes in a Metal-Based Composite Coating and Composites