Abstract:Abstract Here, numerous oxygen-containing functional groups were grafted onto the surface of CNTs to improve their dispersibility in an electrolyte. The CNTs were characterized by FT-IR, Raman, XPS, FE-SEM, and TEM. The results revealed that the dispersibility of the functionalized CNTs in the composites was better than unfunctionalized CNTs. CNTs/Ni composites were deposited on a copper plate by pulsed electrodeposition and ultrasonic dispersion using an electrolytic bath with CNTs concentrations from 0 to 2 g l −1 . The friction and wear behavior of the composite coatings were assessed using two different methods. In the first method, the coatings were scratched with a progressively higher load from 0–100 N, and the results demonstrate a 10 percent reduction in the coefficient of friction (COF) of the composite compared to pure nickel. The other method involved applying a constant load of 30 N, the COF and microscopic wear mechanism were investigated at different carbon nanotube contents, and the results confirmed that the COF of the composites was gradually reduced with the increase of carbon nanotube mass concentration, and the COF was only 0.343 when the carbon nanotube content was increased to 2 g l −1 . According to the XRD results, increasing the CNTs contents changed the preferred growth orientation. Moreover, the FE-SEM images of the wear surface of the 1 g l −1 CNTs/Ni sample indicated that it had the best wear resistance and showed the smoothest wear trace without apparent cracks. The addition of CNTs enhanced the wear resistance of the nickel matrix due to the superior mechanical strength and lubricating effect of the CNTs. CNTs exposed to the matrix surface reduced the direct contact between the Ni matrix and the friction pair, acted as lubricants, and reduced the wear rate.

Friction and wear behaviors of electrodeposited Ni-P-CNTs composite coatings on Al-alloy substrate

Preparation of Ni-Cnt Composite Coatings on Aluminum Substrate and Its Friction and Wear Behavior

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Friction and wear behavior of Ni-P-carbon nanotubes (CNTs) electroless composite coating

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

Friction and Wear Behavior of Electroless Ni-Based Cnt Composite Coatings

SYNTHESIS AND THE PERFORMANCE OF CARBON NANOTUBES-(Ni-P) COMPOSITES

Investigation of the microstructure and tribological properties of CNTs/Ni composites prepared by electrodeposition

Friction and wear resistance of the electroless Ni-P-CNTs composite coatings

Electroless Preparation and Tribological Properties of Ni-P-Carbon Nanotube Composite Coatings under Lubricated Condition

Friction and wear behavior of Ni-based carbon nanotubes composite coatings

Tribological properties of Ni–P-multi-walled carbon nanotubes electroless composite coating

Influence on (Ni-P) Electroless Composite Plating with Carbon Nanotubes

Preparation and Self-Lubricity Investigation of CNTs/Ni Composite Coatings under Severe Conditions

Tribological Application of Carbon Nanotubes in a Metal-Based Composite Coating and Composites

Friction and Wear Behavior of Electroless Wear-Resistant and Self-Lubricating Ni-P Composite Coatings

Carbon Nanotubes Improves the Tribological Properties of Ni60/Al<sub>2</sub>O<sub>3</sub> Coatings

Hard and Corrosion-Resistant Ni-xAl-yTi Nanocomposite Coatings for CNT/Al Composites

Preparation and Properties of Ni–Co–P/nano‐sized Si3N4 Electroless Composite Coatings

Influences of Mwcnts Concentration on the Friction and Anti-Wear Behavior of Ni-P Coating

Fabrication and Tribological Properties of Carbon Nanotubes-Aluminum Composites