Abstract:Abstract Here, numerous oxygen-containing functional groups were grafted onto the surface of CNTs to improve their dispersibility in an electrolyte. The CNTs were characterized by FT-IR, Raman, XPS, FE-SEM, and TEM. The results revealed that the dispersibility of the functionalized CNTs in the composites was better than unfunctionalized CNTs. CNTs/Ni composites were deposited on a copper plate by pulsed electrodeposition and ultrasonic dispersion using an electrolytic bath with CNTs concentrations from 0 to 2 g l −1 . The friction and wear behavior of the composite coatings were assessed using two different methods. In the first method, the coatings were scratched with a progressively higher load from 0–100 N, and the results demonstrate a 10 percent reduction in the coefficient of friction (COF) of the composite compared to pure nickel. The other method involved applying a constant load of 30 N, the COF and microscopic wear mechanism were investigated at different carbon nanotube contents, and the results confirmed that the COF of the composites was gradually reduced with the increase of carbon nanotube mass concentration, and the COF was only 0.343 when the carbon nanotube content was increased to 2 g l −1 . According to the XRD results, increasing the CNTs contents changed the preferred growth orientation. Moreover, the FE-SEM images of the wear surface of the 1 g l −1 CNTs/Ni sample indicated that it had the best wear resistance and showed the smoothest wear trace without apparent cracks. The addition of CNTs enhanced the wear resistance of the nickel matrix due to the superior mechanical strength and lubricating effect of the CNTs. CNTs exposed to the matrix surface reduced the direct contact between the Ni matrix and the friction pair, acted as lubricants, and reduced the wear rate.

Preparation of Electrodeposited Ni-CNTs Nanocomposite Coatings with Highly Wear and Corrosion Resistance Properties

Influence on (Ni-P) Electroless Composite Plating with Carbon Nanotubes

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

SYNTHESIS AND THE PERFORMANCE OF CARBON NANOTUBES-(Ni-P) COMPOSITES

Electroless Preparation and Tribological Properties of Ni-P-Carbon Nanotube Composite Coatings under Lubricated Condition

Preparation of Ni-Cnt Composite Coatings on Aluminum Substrate and Its Friction and Wear Behavior

Investigation of the microstructure and tribological properties of CNTs/Ni composites prepared by electrodeposition

Friction and wear behaviors of electrodeposited Ni-P-CNTs composite coatings on Al-alloy substrate

Friction and wear behavior of Ni-based carbon nanotubes composite coatings

Tribological properties of Ni–P-multi-walled carbon nanotubes electroless composite coating

Mechanical and Corrosion Resistance Properties of Tio2 Nanoparticles Reinforced Ni Coating by Electrodeposition

Enhanced Wear Performance of Cu-Carbon Nanotubes Composite Coatings Prepared by Jet Electrodeposition.

Friction and wear behavior of Ni-P-carbon nanotubes (CNTs) electroless composite coating

Electrochemical Properties and XPS Analysis of Ni-B/SiC Nanocomposite Coatings

Fabrication and characterization of CNT-reinforced Ni-Co composite coatings: microstructural evolutions and corrosion behavior

Preparation and Corrosion Resistance of Ni-W-CF Composite Coating on P110 Steel

Friction and Wear Behavior of Electroless Ni-Based Cnt Composite Coatings

Tribological Application of Carbon Nanotubes in a Metal-Based Composite Coating and Composites

Preparation and characterisation of the Ni-C composite coating electrodeposited with carbon sol

Preparation and Properties of Ni–W Composite Coatings Reinforced by Graphene Nanoplatelets

Preparation of Chromium Carbide-Strengthened Ni-W Coatings by Electrodeposition and the Corresponding Anticorrosion Behavior in CO2-Saturated NaCl Solution