Abstract:Abstract Here, numerous oxygen-containing functional groups were grafted onto the surface of CNTs to improve their dispersibility in an electrolyte. The CNTs were characterized by FT-IR, Raman, XPS, FE-SEM, and TEM. The results revealed that the dispersibility of the functionalized CNTs in the composites was better than unfunctionalized CNTs. CNTs/Ni composites were deposited on a copper plate by pulsed electrodeposition and ultrasonic dispersion using an electrolytic bath with CNTs concentrations from 0 to 2 g l −1 . The friction and wear behavior of the composite coatings were assessed using two different methods. In the first method, the coatings were scratched with a progressively higher load from 0–100 N, and the results demonstrate a 10 percent reduction in the coefficient of friction (COF) of the composite compared to pure nickel. The other method involved applying a constant load of 30 N, the COF and microscopic wear mechanism were investigated at different carbon nanotube contents, and the results confirmed that the COF of the composites was gradually reduced with the increase of carbon nanotube mass concentration, and the COF was only 0.343 when the carbon nanotube content was increased to 2 g l −1 . According to the XRD results, increasing the CNTs contents changed the preferred growth orientation. Moreover, the FE-SEM images of the wear surface of the 1 g l −1 CNTs/Ni sample indicated that it had the best wear resistance and showed the smoothest wear trace without apparent cracks. The addition of CNTs enhanced the wear resistance of the nickel matrix due to the superior mechanical strength and lubricating effect of the CNTs. CNTs exposed to the matrix surface reduced the direct contact between the Ni matrix and the friction pair, acted as lubricants, and reduced the wear rate.

Influences of Mwcnts Concentration on the Friction and Anti-Wear Behavior of Ni-P Coating

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

Influence on (Ni-P) Electroless Composite Plating with Carbon Nanotubes

Preparation of Ni-Cnt Composite Coatings on Aluminum Substrate and Its Friction and Wear Behavior

Friction and Wear Behavior of Electroless Ni-Based Cnt Composite Coatings

SYNTHESIS AND THE PERFORMANCE OF CARBON NANOTUBES-(Ni-P) COMPOSITES

Friction and wear behavior of Ni-P-carbon nanotubes (CNTs) electroless composite coating

Friction and wear behaviors of electrodeposited Ni-P-CNTs composite coatings on Al-alloy substrate

Tribological properties of Ni–P-multi-walled carbon nanotubes electroless composite coating

Friction and wear behavior of Ni-based carbon nanotubes composite coatings

Tribological Application of Carbon Nanotubes in a Metal-Based Composite Coating and Composites

Electroless Preparation and Tribological Properties of Ni-P-Carbon Nanotube Composite Coatings under Lubricated Condition

Friction and Wear Behavior of Electroless Wear-Resistant and Self-Lubricating Ni-P Composite Coatings

Effect of PDDA‐MWCNTs concentration on the microstructure and friction behavior of Co‐doped diamond‐like carbon (Ni/N/MWCNTs‐DLC) films

Investigation of the microstructure and tribological properties of CNTs/Ni composites prepared by electrodeposition

Influence of processing parameters on final characteristics of Ni-P-MWCNT coatings produced by pulsed electrodeposition

Tribological Behavior of Multi-Walled Carbon Nanotube/Epoxy Resin Nanocomposites

Influence of Ti3C2Tx Addition on the Corrosion Behaviour and Tribological Properties of Electrodeposited Ni-W-Ti3C2Tx Nanocomposite Coatings

Study on the friction and wear properties of nickel-based-WC-10Ni composite coatings prepared on the surface of TC4 titanium alloy

Investigation of the effect of lubricant properties of carbon nanomaterial in Cu/MWCNT composites on wear

Study of the effect of amino-functionalized multiwall carbon nanotubes on dry sliding wear resistance properties of carbon fiber reinforced thermoset polymers