Abstract:Ni–SiC nanocomposite coatings were prepared on a brass substrate by electrocodeposition. The electrodeposition was carried out by adding the SiC nanoparticles to a nickel-containing bath. Nickel deposition processes were analyzed by cathodic polarization curves, and the plating parameters were determined preliminarily by analyzing the effects of different technological parameters on the deposition process. Then, electrocodeposition processes were carried out with different concentrations of SiC nanoparticles in the bath. The effects of current density, stirring rate, and SiC nanoparticle’s concentration in the plating bath on the hardness of coatings were investigated by microhardness tests. Besides the microhardness tests, wearing tests and corrosion tests were also applied to the coatings with the highest hardness and coatings of pure nickel. The structures and surface morphologies of the coatings were examined by X-ray diffraction (XRD) and scanning electron microscopy (SEM) methods. The experimental results show that the microhardness of the codeposited coating increases with increasing current density and attains a maximum at the SiC concentration of 6 g/L. The decrease in the microhardness at higher SiC concentrations may be due to agglomeration of nanosized particles in the plating bath. Increasing the stirring speed did not give a better quality deposition as coatings produced at low stirring rates always had higher microhardness values than did those at high stirring rates. Furthermore, the Ni–SiC nanocomposite coatings have lower friction coefficient and better corrosion resistance than those of pure nickel coatings.

Influence of processing parameters on final characteristics of Ni-P-MWCNT coatings produced by pulsed electrodeposition

Influences of Mwcnts Concentration on the Friction and Anti-Wear Behavior of Ni-P Coating

Influence on (Ni-P) Electroless Composite Plating with Carbon Nanotubes

Fabrication and characterization of CNT-reinforced Ni-Co composite coatings: microstructural evolutions and corrosion behavior

The Influence of Pulse Plating Parameters on the Structure and Corrosion Behavior of Ni-W-TiC Nanocomposite Coatings

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

Effect of Current Density and Bath Temperature to The Corrosion and Wear Behaviour of Tungsten Carbide - Nickel Electrodeposition Coating

Effect of Pulse Electrodeposition Mode on Microstructures and Properties of Ni-TiN Composite Coatings

Friction and wear behaviors of electrodeposited Ni-P-CNTs composite coatings on Al-alloy substrate

DRY AND HOT CORROSION BEHAVIOUR OF Al-Ni-Co-x MWCNT COMPOSITES PROCESSED THROUGH POWDER METALLURGY

Influence of Electrodeposition Process Parameters and Si3N4 Nanoparticle Concentration on Microhardness and Wettability of Ni-Co-Si3N4 Nanocomposite Coatings

Effect of hydroxyapatite‐titanium‐MWCNTs composite coating fabricated by electrophoretic deposition on corrosion and cellular behavior of NiTi alloy

Preparation and characterization of Ni-P-Al2O3-PTFE nanocomposite coatings by unidirectional jet electrodeposition

Enhanced mechanical and wear properties of Ni-W-SiC composite coatings by synergistic influence of micro-nano SiC mixture

Enhancement of Corrosion and Wear Resistance of Ni-P Coatings Stems from the Synergistic Effects of Cr3C2 and Heat Treatment

Effect of TiN concentration on microstructure and properties of Ni/W–TiN composites obtained by pulse current electrodeposition

Synthesis and characterization of nickel–cobalt spin coatings reinforced with carbon nanotubes: microstructural properties, microhardness, and corrosion resistance

Micromechanical Analysis of Metal-Ceramic Thin-Films on Steel Substrates

Adding WC Nano-particles to Nickel-Based Coating Deposited by PTA Process: Microstructure and Nanoindentation Hardness Characteristics

A Study on the Electrocodeposition Processes and Properties of Ni–SiC Nanocomposite Coatings

Preparation and Corrosion Resistance of Ni-W-CF Composite Coating on P110 Steel