Abstract:High-density embedded nonvolatile memory (eNVM) at advanced technology nodes is still in great demand for SOC chips used in consumer electronics, self-driving cars, industrial control, and IoT edge devices. Although embedded NOR Flash is still main stream, its process complexity and high integration cost make it difficult to scale beyond 28nm. RRAM has become a promising alternative owing to its excellent scalability, low power, and compatibility with logic processes [1 -6]. However, several challenges still exist that restrict RRAM from practical eNVM applications, as shown in Fig. 24.2.1. 1) a high supply voltage is needed, because of high operation voltages and a considerable voltage drop on write path. 2) The IR drop on write path varies significantly with the distance of a cell from the peripheral circuits. 3) Prior self-write termination (SWT), with its abrupt cutoff, fails to form dense conductive filaments (CFs). While delayed termination helps to alleviate this issue, its delay time is not optimized for fast and slow cells [3]. 4) Previous read reference schemes that use a small number of HRS/LRS cells may collapse when encountering tail bits, resulting in a poor reference [6]. In this work, we demonstrate a 1Mb 14nm-FinFET RRAM with a 0.022 μm <sup>2</sup> cell size. The cell array is in a deep N-well with adequate P-substrate biasing to alleviate the difficulty of high voltage transfer. Placing the bit line (BL) and source line (SL) drivers on the top and bottom of the array reduces the IR-drop variation for near and far cells. Self-adaptive delayed termination (SADT) adjusts the termination time according to cell characteristics (fast or slow), helping to generate robust CFs. A read reference with multiple dummy 1T1R cells avoids the reference collapse issue. The test chip supports reliable read operation at a minimum supply voltage of 0.5V from -40°C to 125°C.

The Design of Low-power Embeded SRAM for TFT-LCD Driver IC

Design of an Embedded High Speed Dual-Port SRAM in Display Control/Driver ICs

An Ultra-Low-power 1 Kb Sub-Threshold SRAM in the 180 Nm CMOS Process

Design of a Dual-Port SRAM in OLED Display Driver ICs

A Novel TFET-MOSFET Hybrid SRAM for Ultra-Low-Power Applications

A Dual Core Oxide 8T SRAM Cell with Low Vccmin and Dual Voltage Supplies in 45nm Triple Gate Oxide and Multi Vt CMOS for Very High Performance Yet Low Leakage Mobile SoC Applications

A 3.75mb Embedded RRAM IP on 40nm High-Voltage CMOS Technology

Design and Implementation of RRAM Voltage Supply Circuits

Bit-Interleaving-Enabled 8t Sram with Shared Data-Aware Write and Reference-Based Sense Amplifier

Dynamic Power Reduction in a Novel CMOS 5T-SRAM for Low-Power SoC

Design of 512-Kbit Synchronous High-speed SRAM

Novel 15T SRAM Cell for Low Voltage High Reliability Application

Column-Selection-Enabled 10T SRAM Utilizing Shared Diff-VDD Write and Dropped-VDD Read for Power Reduction

Highly Area-Efficient Low-Power SRAM Cell with 2 Transistors and 2 Resistors

A 0.13 µm 8 Mb Logic-Based Cu Si O ReRAM With Self-Adaptive Operation for Yield Enhancement and Power Reduction

Circuits and Implementation of a Low-Power Embedded EEPROM Memory

A low-Power SRAM with charge cycling based read and write assist scheme

Pure logic CMOS based embedded Non-Volatile Random Access Memory for low power RFID application

24.2 A 14nm-FinFET 1Mb Embedded 1T1R RRAM with a 0.022µm<sup>2</sup> Cell Size Using Self-Adaptive Delayed Termination and Multi-Cell Reference

An 8t/cell FeFET-Based Nonvolatile SRAM with Improved Density and Sub-fJ Backup and Restore Energy

Resonant Energy Recycling SRAM Architecture