Abstract:Studying the tribological behavior between diamond materials and ceramics is crucial for understanding the grinding mechanism of diamond wheels on ceramics. To comprehend the tribological characteristics between diamond materials and various ceramics, this paper presents a comparative study of the tribological behaviors of Al2O3, AlN, Si3N4, and ZrO2 ceramics sliding against polycrystalline diamond (PCD) balls. The dependence of the coefficient of friction (COF), wear characteristics as well as the surface morphology of different ceramics and SiC-bonded PCD balls on load, sliding stage were examined. The effect of nanofluids on the COF and wear of different ceramics was also investigated. The results showed that the tribological characteristics of ceramic materials are strongly dependent on mechanical properties. Al2O3 and AlN ceramics with lower fracture toughness exhibit a significantly higher COF and wear volume than that of Si3N4 and ZrO2 ceramics. Al2O3 presents the highest COF (0.38) and wear volume, and Si3N4 owns the lowest COF (0.08) and wear volume under the load of 9.8 N. By examining the wear grooves of different ceramics, it is found that Al2O3 and AlN ceramics own larger debris than that of Si3N4 and ZrO2, which also causes more smearing on the ceramic and adhesion of wear debris to the SiC-bonded PCD ball for Al2O3 and AlN. Under lubricants, the COFs and the adhesion of wear debris are effectively reduced, and the wear rate of the ceramic is increased. There is little difference between deionized (DI) water and nanofluids on the effect of lubricants on COF for Al2O3 and AlN. However, for ceramics with higher fracture toughness, the nanofluids can reduce the COFs of Si3N4 and ZrO2 in comparison with DI water.

Tribological Characteristics of Si3N4 Ceramic Sliding on Stainless Steel

Friction and Wear of Si3N4 Ceramic/stainless Steel Sliding Contacts in Dry and Lubricated Conditions

Wear Behavior of Si3N4 Ceramic Cutting Tool Material Against Stainless Steel in Dry and Water-Lubricated Conditions

Wear mechanisms of Ti(C, N) ceramic in sliding contact with stainless steel

Wear Behavior of Al 2 O 3 -Ticn Composite Ceramic Sliding on Stainless Steel

Tribological Characteristics of Silicon Nitride-chilled Cast Iron with Oil-less Lubrication

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Friction and Wear Properties of Si3N4 and SiC Used for Water-Lubricated Sliding Bearings

Investigation on the tribological properties of ceramics rubbing against stainless steel at high temperature

Analysis on Wear Properties and Impact Factors for Si3N4 Ceramic Mated with Chilled Cast Iron

Wear mechanisms of pairs of Si3N4-based and Ti(CN)-based ceramic with 1Cr18Ni9Ti stainless steel under dry-friction condition

Cutting performances and their failure mechanisms of ceramic tools for cutting stainless steel

Tribological Behavior and Wear Mechanism of Cu-SiO2 Sintered Composite under Different Sliding Speeds

Friction and wear behaviors of Al 2 O 3 /TiC micro-nano-composite ceramic sliding against metals and hard materials

Tribological Properties of Ti3SiC2 Coupled with Different Counterfaces

A comparative study on tribological behavior of Al2O3, AlN, Si3N4 and ZrO2 ceramics sliding against polycrystalline diamond ball

Research on Tribology Property of Si-3N-4 Ceramic and Chilled Iron under Oil-Less Lubrication

Tribocorrosion behavior of 316L stainless steel sliding against different ceramics in 0.5 M H2SO4 solution

High-temperature tribological properties of Si 3 N 4 /TiC ceramic with bionic surface textures and DLC coatings

Friction and Wear Properties of CrSiCN/SiC Tribopairs in Water Lubrication

STUDY ON THE WEAR PERFORMANCES OF CERAMIC TOOLS FOR MACHINING 304 STAINLESS STEEL