Abstract:Assorted morphologies of precipitates in fcc/bcc transformation systems have been reported, which often exhibit irrational characteristic. Various models have been developed to explain the habit plane (or the broad facet), but the overall morphologies of the precipitates are seldom explained quantitatively. In this work, the equilibrium cross-section of rod-shape austenite precipitates in duplex stainless steel is determined by atomistic simulation. The input orientation relationship (OR) between fcc and bcc phase is determined according to the O-line criterion (one of the interfaces contains a single set of dislocations), with the condition that the invariant line lies in close-packed plane pair of (1 (1) over bar(1) over bar)(f)|(10 (1) over bar)(b) and the Burgers vector of O-lines is [011](f|)/2|((1) over bar 11)(b)/2. The obtained OR is close to the K-S OR ((11 (1) over bar)(f)//(01 (1) over bar)(b), [101](f)//(111)(b)), with the deviation of 1.27 degrees from the parallelism in both planes and directions. Interfacial energy of interfaces in various orientations in the zone axis of the invariant line ([0.75 0.10 0.65](f)//[0.52 0.68 0.52](b)) has been calculated. To ensure the reliability of the calculated values, an initial atomic configuration free of interstitial and vacancy is constructed for each interface. The energies of the O-line interface, the interface normal to either Delta g(((1) over bar 11)) or Delta g((020)) are found to have similar values, each at a local minimum. Based on the calculated interfacial energies, the equilibrium cross-section morphology is determined by the Wulff construction. The result shows that the morphology exhibits a near rhombus cross-section, which agrees consistently with experiments. One of the major facets is the O-line interface, normal to ((0.66) over bar 0.12 0.74)(f)//((0.51) over bar (0.24) over bar 0.83)(b), in agreement with the observation. The other facet is normal to Delta g((020)) (((0.25) over bar (0.87) over bar 0.42)(f)//(0.45 (0.73) over bar 0.51)(b)) in the calculated result, while it is normal to Delta g(((1) over bar 11)) (((0.36) over bar (0.77) over bar 0.53)(f)//(0.31 (0.71) over bar 0.63)(b)) in experimental results, with about 10 degrees difference between them. The discrepancy between calculated and observed results is probably because the experiments have not reached the equilibrium state. The dislocation structures in these three interfaces are identified from the atomic simulation results by a newly developed method based on the singular value decomposition of the Nye tensor. It confirms that the O-line interface contains a single set of [011](f)/2 dislocations with spacing of 1.5 nm. The interface normal to either Delta g(((1) over bar 11)) or Delta g((020)) contains two sets of dislocations. The dislocation structure in the facet normal to Delta g((1) over bar 11)) is in good agreement with experimental observation of the non-O-line facet, including the local decomposition of dislocation core to (1 (1) over bar(1) over bar)(f) stacking faults.

Three-dimensional analysis of ferrite allotrimorphs nucleated on grain boundary faces, edges and corners

Three-Dimensional Morphology and Growth Behavior of Ferrite Allotriomorphs Formed at Grain Boundary Edges

Serial Sectioning And 3d-Reconstruction Of Ferrite Allotriomorphs Nucleated At Grain Boundary Faces In An Fe-C-Mn Alloy

Three-dimensional Morphology of Grain Boundary Widmanstätten Ferrite in a Low Carbon Low Alloy Steel

Growth Behavior of Ferrite Allotriomorphs Nucleated on Grain Boundary Faces in a Low Carbon Steel

Three-Dimensional Observation and Growth Kinetics of Proeutectoid Ferrite Formed at Austenite Grain Boundary in A Low Carbon Microalloyed Steel

Phase field molding on the morphologies and growth kinetics of grain boundary ferrite allotriomorphs

New Insights into Intragranular Ferrite in a Low-Carbon Low-Alloy Steel

Study on Three-Dimensional Morphology of Intragranular Nucleating Ferrites in Low Carbon Steels

Three-Dimensional Growth of Coherent Ferrite in Austenite: A Molecular Dynamics Study

Nucleation and Three-Dimensional Morphology of Intragranular Ferrite in A Vanadium Microalloyed Steel

Three-dimensional analysis of acicular ferrite in a low-carbon steel containing titanium

In Situ Observation of Acicular Ferrite Formation and Grain Refinement in Simulated Heat Affected Zone of High Strength Low Alloy Steel

Multiple morphologies and twin structure generated by a definite growth behavior of grain boundary M 23 C 6 in tempered Fe–15Mn–3Al-0.7C steel

Simulation of Nucleation of Proeutectoid Ferrite at Austenite Grain Boundaries During Continuous Cooling

In-Situ Observations of Acicular Ferrite Growth Behavior in the Simulated Coarse-Grained Heat-Affected Zone of High-Strength Low-Alloy Steels

Three-Dimensional Morphology and Growth Behavior of Acicular Ferrite in Low Carbon Steel Weld

Three-dimensional morphology and analysis of ferrite in steels

Emergence of near-boundary segregation zones in face-centered cubic multi-principal element alloys

Nucleation of Austenite from Pearlitic Structure in an Fe–0.6C–1Cr Alloy

An Investigation on the Equilibrium Morphology and Interfacial Structures of Pricipitates in Duplex Stainless Steel by Atomistic Simulation