Abstract:For aluminum-based alloy particles, the addition of alloying element lithium (Li) with the properties of a high chemical activity and a low melting/boiling point can significantly improve the thermo-reactive properties of aluminum (Al) particles. To further reveal the combustion mechanism, this paper presents the nitriding reaction and combustion characteristics of Al-Li alloy in nitrogen (N 2 ) through thermogravimetric analysis and differential scanning calorimetry (TG-DSC) analysis at a low heating rate and laser-induced ignition experiments at a high heating rate, considering the influences of two kinds of Li contents (1.0 wt% @ Al-1.0Li and 2.5 wt% @ Al-2.5Li) on these characteristics and making a comparison to the counterpart Al. Al-Li alloy powders as-prepared by gas atomization method showed the texture of the Li-rich eutectic phase compounds on the surface by scanning electron microscope (SEM) characterization. The TG-DSC results demonstrated that the thermal nitriding reaction of Al-Li alloy in N 2 was significantly faster than that of pure Al. The nitriding reaction temperature decreased from 853 °C for pure Al to 245 °C for Al-2.5Li alloy with a reduction of 71 %. The final weight gain of Al-2.5Li alloy was almost three times higher than that of pure Al in N 2 . The SEM photograph of intermediate nitriding products revealed that the cracks and loose "island" structures in the Li-rich zone on the Al-Li surface were the key to preventing the formation of a "passivation effect" into Al and promoting N 2 uptake during melting. In addition, Li also acts as a catalytic carrier and "oxygen absorber" to enhance the Al-N reaction. The combustion of single Al-Li alloy microparticles induced by laser showed two stages: preheating and rapid nitriding. Al-Li alloy particles were ignited more rapidly and showed typical gas-phase / surface combustion modes different from pure Al. According to these findings, the combustion mechanism was proposed to help guide the development of Al-based solid propellants containing Li and the synthesis of AlN/Al composites in nitrogen-rich environments.

Effects of Supergravity Conditions on Combustion Synthesis of NiAl Intermetallies

Effects of Super-gravity Field on Solidification Structure and Microhardness of Al-Ni-Cr Alloy

Effect of Substrate Characteristics on Interdiffusion Coefficients of Ni and Al Atoms in Β-Nial Phase of Aluminide Coatings

Combustion synthesis of Ti(C, N) TiB2 composite powders under super gravity conditions

Combustion Synthesis of Ti(C,N)-TiB_2 Composite Powders under Super Gravity Conditions

Combustion synthesis of porous TiC/Ni composites under high gravity

Combustion synthesis of NiAl2O4 spinel powder

Fabrication of Bulk Al2o3 by Combustion Synthesis Melt-Casting under Ultra-High Gravity

Microstructure and formation mechanism of Ni-Al intermetallic compounds fabricated by reaction synthesis

Dissolution–precipitation mechanism of self-propagating high-temperature synthesis of mononickel aluminide

Laser-Induced Ignition and Combustion of Single Micron-Sized Al-Li Alloy Particles in High Pressure Air/N2

Preparation of W-Ni graded alloy by combustion synthesis melt-casting under ultra-high gravity

Enhancement effect of Li addition on nitriding reaction and combustion of Al-Li alloy in N 2

Combustion synthesis of Ti3SiC2 under high-gravity condition

Effects of starting compositions on the phase composition and microstructure of Yb α-SiAlON prepared by combustion synthesis

EFFECTS OF TiAl ADDITION ON COMBUSTION SYNTHESIS OF Ti_2AlC

Effect of a NiO Additive on Interaction in a Ni–Al–W System in Self-Propagating High-Temperature Synthesis

The Effect of the Nucleation Ability on Solidified Microstructures of Gas-Atomized Fe–6.5 Wt.%si Alloy Powder

Combustion Synthesis of NiAl/TiC Multiphase Composites and their Related Microstructure

Effects of TiAl additions on combustion synthesis of Ti3AlC2 powders

Mechanism and Kinetics Analysis of AlN Combustion Synthesis