Abstract:This study aimed to enhance the sinterability and conductivity of yttria fully stabilized zirconia electrolyte through co-doping by 2 mol% of ZnO and different contents of MnO 2 (0, 0.5, 1, 1.5 mol%) at two sintering temperatures of 1300 and 1400 °C. Phase composition identification, density, microstructure, and conductivity of the samples were evaluated using X-ray diffraction (XRD), Archimedes' method, field emission scanning electron microscopy (FESEM), and electrochemical impedance spectroscopy (EIS), respectively. The XRD results revealed that ZnO and MnO 2 are successfully doped in the fluorite structure of YSZ sintered at 1400 °C, and the cubic structure is completely preserved. However, at a sintering temperature of 1300 °C, the (111) peaks of doped samples were slightly split, which implied a slight phase transformation of YSZ from cubic to a tetragonal structure. The co-doped samples, at both sintering temperatures, showed higher relative density and grain size compared with pure YSZ. The addition of 2 mol% of ZnO and 0.5 mol% of MnO 2 at 1400 °C increased the relative density of YSZ from 81.6% to 95.1%. The increase in relative density and grain size, while maintaining the cubic structure, caused an increase in the conductivity of the mentioned sample. Compared with pure YSZ, the sample's total conductivity increased from 7.37 to 10.03 S m −1 at 800 °C. The proposed composition showed better sintering behavior, lower activation energy of grain conductivity, and higher conductivity than pure YSZ. This behavior is thought to be due to the facilitating rearrangement of atoms during sintering and an increase in oxygen ion vacancy concentration due to co-doping with the appropriate amount of ZnO and MnO 2 .

Chemical Synthesis and Conductivity Study of Doped Mullite Solid-Solutions

The Effects of Mineral Composition and Sintering Temperature on Synthetic Mullite

A new chemical method for preparation of both pure and doped mullite

The oxygen ion conductivity of mullite prepared using a wet chemical process

Effect of transition metal ion pairs doping on the dielectric properties of mullite derived by sol–gel route

Enhancing sintering behavior and conductivity of YSZ electrolyte by co-doping of ZnO and MnO 2

Effect of Y2O3 on Synthesizing Mullite from High Alumina Fly-Ash

Synthesis and Controlled Growth of Mullite Submicron Powders

Mullite Fibers Prepared by Sol-Gel Method Using Aluminum Chloride Aluminum Isopropoxide and Tetraethylorthosilicate

Synthesis of mullite ceramics from powdered mine tailings reinforced with Al2O3

A comparative electrical study of nano-crystalline mullite with low dielectric loss due to incorporation of tungsten and molybdenum ion: their uses in electronic industries

Synthesis and Characterization of Ti, Fe-Doped Mullite-I

Effect Of Y2o3 On Property Of Mullite Ceramic Enhanced By Andalusite

Fabrication and characterization of porous mullite ceramics with ultra-low shrinkage and high porosity via sol-gel and solid state reaction methods

Synthesis of Mullite Using Low-Grade Bauxite and Coal Gangue

Preparation of mullite ceramics with equiaxial grains from powders synthesized by the sol-gel method

Preparation and properties of porous mullite-based ceramics fabricated by solid state reaction

HYDROLYSIS-ASSISTED SOLIDIFICATION OF MULLITE GREEN BODY

Study on Synthesis and Electronic Conductivities of Y_xTi_2O_n(1.7≤x≤2.1) System as Solid State Electrolytes by co-Precipitation

Effect of Y<sub>2</sub>O<sub>3</sub> on the Sintering, Mechanical and Dielectric Properties of Mullite/h-BN Composites

Low-temperature Synthesis of Highly Porous Whisker-Structured Mullite Ceramic from Kaolin