Analysis of maloperation on the REB103 busbar protection

GAO Xiang,BAO Wei

DOI: https://doi.org/10.3969/j.issn.1674-3415.2006.13.020

2006-01-01

Abstract:REB103 is a mid-impedance differential relay for busbar protection.But under some certain circumstances,it would be maloperated when external fault occurs.The fault cause and analysis under this work condition are detailed and some schemes to avoid its happening again are proposed.

What problem does this paper attempt to address?

Study on the differential protection of busbar with magnetic restraint

li zhongan,he benteng

DOI: https://doi.org/10.3969/j.issn.1674-3415.2000.09.003

2000-01-01

Abstract:It proposes a method of detecting the secondary resistance R of CT on real time based on the principle of magnetic restraint differential protection for busbar. The simulation result shows that with this method, the initial saturation point of CT can be found correctly in despite of the influence from current transient and harmonics. It also can protect the magnetic restraint busbar protection from mal-operation possibly caused by variation of the secondary load of CT.
Design of a residual current circuit breaker IC with anti-interference technique

Cheng Peng,Yan Han,Zhen-Qi Fan,Wen Fu,Xing-Gan Guo

DOI: https://doi.org/10.1007/s10470-009-9430-7

IF: 1.321

2009-01-01

Analog Integrated Circuits and Signal Processing

Abstract:Residual current circuit breakers (RCCB) is the equipment which protect human body from an electric shock, there is close relation between RCCB and human safety. However, shortages still exist. Current RCCB tend to cause nuisance tripping due to their sensitive reaction to the interference signal in the actual power grid. So, the RCCB cannot work at the crucial moment effectively. This paper analyzes the impact to the RCCB from the general interference signal and induced interference signal in power grid, and this paper also introduces a new technique—10 ms non-actuating time technique, which is used to stand aside the interference signal. This technique with delay time protection and other anti-interference technique are integrated into a special RCCB IC chip, which is fabricated in a mixed-signal 0.5 µm CMOS process in CSMC. The test results verify great improvement in RCCB performance. Additionally, this paper analyzes the disadvantage of the active national standard referring to RCCB in China and presents some suggestions for the improvement.
ANALYSIS AND COUNTERMEASURE FOR MISOPERATION OF LONGITUDINAL DIFFERENTIAL PROTECTION WITH UNCLEAR REASON

Wang Weijian,Li Fuying

DOI: https://doi.org/10.3321/j.issn:1000-1026.1999.18.005

1999-01-01

Abstract:Longitudinal differential protections for electric main equipments (transformer, generator, motor, busbar, etc. ) misoperate frequently under normal operation, and the same misoperation occurs over and over again. "Cause is not clear" is often the conclusion. This paper analyzes the transient performance of current transformer in the protective level. It is pointed out that TP class current transformer is too expensive for medium and low voltage device, and also difficult to install because of its bulky size. Digital optical current transducer (DOCT) has been developed successfully, which provides possibility to solve the said problems.
Maloperation Analysis and Preventive Measures of 500 kV Reactor Protection

Li Haisheng,Yang Shaoyuan Yang Xuefei,Yang Xuefei, Yang Shaoyuan

DOI: https://doi.org/10.1088/1742-6596/1449/1/012048

2020-01-01

Journal of Physics: Conference Series

Abstract:Abstract This paper introduces the process of checking, analyzing and dealing with the causes of maloperation of the first set protection of 500 kV reactor in a substation. By checking the secondary circuit of 500 kV reactor protection for power outage, it is analyzed that the main cause of reactor protection malfunction is that the cable core of the current circuit of the first set protection is damaged at the secondary terminal box of TA of the high voltage casing pipes, which causes the induction current to enter in series, the abnormal sampling of the first set of protection B phase, and the protection outlet action. Aiming at the existing problems, this paper gives corresponding treatment methods and preventive measures.
Analysis of the Adaptive Scheme of Identifying the Substituting Situation

Ling-ling HUANG,Ben-teng HE

DOI: https://doi.org/10.3969/j.issn.1674-3415.2006.15.004

2006-01-01

Abstract:In the substituting situation,bus-bar differential relays may loose the selecting capability because of the wrong differential current mal-operation because of the unknown operation mode during switching situation.After analyzing characters of substituting situation normal situation,this paper presents a new method,based on the isolator auxiliary contact the hands joint,for selecting the proper differential expression,and an and algorithm of two differential expressions in switching operation.It improves the accuracy of differential bus-bar protection provides a new way to make one algorithm for all types of bus arrangements.
Adaptive Distance Relay for Preventing Error Action of Reactive Fault

YU Li-chuang,SHEN Bing,HE Ben-teng

DOI: https://doi.org/10.3969/j.issn.1001-4551.2007.10.012

2007-01-01

Abstract:Impedance between faulted line and ground was generally regarded as a resistance,but in some cases the equivalent impedance can be reactive.The impedance loci with fault impedance seen by the protection in this condition was analyzed.Based on different mal-operation of relay,the solution scheme was given and an adaptive criterion was proposed.The simulation results show that the new adaptive relay has excellent adaptablity and selectivity,can prevent error action,illustrates a good prospect of application and extension.
Performance analysis of multiphase compensated distance relay in single-phase-to-ground fault with power swing

Liu Cui,Xinzhou Dong,Shenxing Shi,Bin Wang,Bak Dominik

DOI: https://doi.org/10.13334/j.0258-8013.pcsee.2013.34.028

2013-01-01

Abstract:An impedance relay is the core element of a distance protection, which is widely applied in power systems. Impedance relay's operation can be affected by power swings. Therefore, a power swing blocking element is required to work with, which makes the distance protection scheme more complex. Using the multiphase compensated distance relay as the base, the resultant distance protection can be made insensitive to the power swings and no additional time blocking element is needed. So, it is valuable to analyze the operation characteristics of multiphase compensated distance relays. By analyzing the relay's equation, this paper reported on the performance of the three elements in multiphase compensated distance relays in the case of a single phase to ground fault during power swings. This paper defined the missing operation's area for a faulty phase element and the maloperation's area for a health phase element. The paper also pointed out the disadvantages of the relay working as the protection of II or III section. PSCAD simulation results verified the conclusions. © 2013 Chin. Soc. for Elec. Eng.
Effect of Reactive Equivalent Fault Impedance on Distance Protection

SHEN Bing,HE Benteng

DOI: https://doi.org/10.3321/j.issn:1000-1026.2006.21.014

2006-01-01

Abstract:Impedance between faulted line and ground is generally regarded as a resistance, but in some cases the equivalent impedance can be reactive. Fault on a transmission line connected to the bus behind the protection is equal to on the bus through a reactive fault impedance. This problem has rarely been noticed. The impedance loci with impedance seen by the protection in this condition is analyzed. The theoretical analysis and digital simulation results show the possibility that distance protection with quadrangular characteristic may mal-operate under this condition.
Analysis on Relay Pretection Actions of 7.20 Failure of Xindian Substation

Yi Ding

2000-01-01

Abstract:It introduces power failure in Xindian Substation and analyses relative relay protection actions.Some technical improvement suggestione are presented.
MAGNETIC RESTRAINING DIFFERENTIAL BUS PROTECT

ma yongsheng,he benteng

1998-01-01

Abstract:Saturation of Current Transformer (CT) is the major problem of Bus Protect in power system.Many measures have been adopted to prevent CT from error operation after saturation,but until now this problem has not been satisfactorily solved for various reasons.On the basis of the physical principle of CT saturation,this paper present a new saturated criterion depending on the flux of CT,and find out a dependable measure to solve the error operation of Differential Bus Protect Coursed by CT saturation theoretically.Furthermore,a Differential Bus Protect technique based on the linear section of CT is presented.
Analysis of a 35kV vacuum circuit breaker accident caused by protection misoperation

Chong Wang,Shan Li,Zhongqiang Zhan

DOI: https://doi.org/10.1117/12.2634855

2022-04-25

Abstract:Reactor equipment is widely used in high-voltage backbone power grid, and its reliability directly affects the safe and stable operation of large power grid. In this paper, a 35 kV Vacuum Circuit Breaker breaking shunt reactor accident in a substation is deeply analyzed. Firstly, the protection misoperation is comprehensively analyzed by means of on-site fault characteristics, theoretical simulation calculation and return to plant disassembly inspection. Secondly, by integrating various information and adopting the analysis method of combining theory with practice and combining in plant traceability and test verification, aiming at the defects of the protection device of the substation, technicians and manufacturers comprehensively inspected the protection device and confirmed that there was an error in the background logic of the monitoring device, resulting in the wrong opening signal. After the manufacturer upgraded the monitoring software, the defect was eliminated. Finally, according to the fault causes, the follow-up countermeasures for such faults are put forward.
Operation Status Monitoring for 500 Kv DC Circuit Breaker with Internal Failures and Relative Backup Fault Isolation Schemes

Weijie Wen,Zhe Zhang,Bin Li,Zhaowei Peng,Yulong Huang

DOI: https://doi.org/10.1016/j.epsr.2024.111204

IF: 3.818

2025-01-01

Electric Power Systems Research

Abstract:As the primary protection and control device in direct current (DC) power systems, DC circuit breakers (DCBs) have complex structures and numerous components, making it prone to diversified internal failures. This paper explores an operation status monitoring method for DCBs, and relative backup fault isolation schemes and system recovery schemes are proposed to handle cases of DCBs with different internal failures. Contributions of this paper are: (1) An operation status monitoring method is proposed to reflect the failure degrees of DCB, categorizing the statuses of DCB into status-1 (normal), status-2 (minor failure) and status-3 (major failure). (2) According to the failure degrees of DCB, relative backup fault isolation and system recovery schemes are proposed to ensure the fault isolation scope is as small as possible and the system could recovery as fast as possible. Simulations are conducted in PSCAD/EMTDC for validation.
Analysis of the Maloperation of Transformer Differential Protection after External Fault Removed

Xiao-yu ZHANG,Da-qiang BI,Peng-sheng SU

DOI: https://doi.org/10.3969/j.issn.1674-3415.2006.01.002

2006-01-01

Abstract:After an external fault of transformer is cleared,the transient flux may enter into the saturation region,and a recovery inrush may be produced.At the same time,the aperiodic component in the fault current usually has a high value during the fault,so that the CT may also enter into the saturation region.Both of them may cause the maloperation of the differential protection.In this paper,the flux of the transformer is obtained by theoretical derivation,then models of transformer and CT are built for simulation,and an experiment is done to prove the results.The factors that affect the inrush are analyzed.The influence on the inrush of the differential protection is investigated and the saturation of CT is studied as well.At last,considering the inrush and the saturation of CT together,the main cause of the maloperation is discussed.
Multiphysics Analysis Of The Busbar In Mmc Submodule Under Dc Pole-To-Pole Fault

Chen Yang,Fan Xie,Bo Zhang,Dongyuan Qiu,Yanfeng Chen

DOI: https://doi.org/10.1109/ICEMS.2019.8922543

2019-01-01

Abstract:The reliability of the submodule in the Modular Multilevel Converter (MMC) directly affects the stable operation of the converter. When the short-circuit current flows through the busbar, the excessive electromagnetic force and thermal stress are imposed to the busbar, which may cause the deformation or even breakage of the busbar. In this paper, the transient analysis of the coupled electric-magnetic-thermal-mechanical field of the busbar in the MMC submodule is carried out under the DC pole -to-pole short-circuit fault. The transient electromagnetic field distribution, temperature rise and displacement of the busbar are shown. The actual structure of the busbar is introduced, and the transient mathematical model of the coupled electric-magnetic -thermal-mechanical of the busbar is established. Then, professional multiphysics simulation software COMSOL is used for analysis. The results show that the deformation in the middle of the busbar is the most serious, and the stress at the corner of the busbar is large. The conclusions obtained can provide reference for the optimization design and reliability evaluation of the MMC submodule.
Study of Rreliability Mmodeling for Rrelay Pprotection Ssystem in Ddigital Ssubstations

何奔腾,李一泉,刘玮,张弛,王超,王慧芳

2013-01-01

Abstract:Compared with the traditional substation relay protection, the structure and content of relay protection system ones in digital substation have changed greatly in structure and content, and there is no standard model and method to evaluate their reliability. Based on the analysis of the formconstitution of digital substation relay protection systems, the information flow is divided into three kinds, which are time synchronization flow, SV flow and GOOSE flow, and their possible topology for each kind of flow is analyzed detailed.. Then it uses the minimal path sets algorithm to calculate the connected rate of three kinds of information flow, and uses series and parallel model to calculate the overall reliability of relay protection systems. At last the paper discusses the software realization of this modeling algorithm, and the example analysis shows that this modeling method provides effective means to evaluate the reliability of different schemes of relay protection systems.
Analysis And Simulation To Spurious Operation Of Sensitive Directional Earth Fault Under Load Switching Condition

Sx Shi,A Wixon,Xz Dong,A Maytt,Brj Caunce

2002-01-01

Abstract:This paper presents the theoretical analysis of intermittent mal-operation of sensitive directional earth fault relays when switching off/on load and simulation tests based on Real Time Digital Simulator (RTDS). The magnitude of the residual current and voltage is dependent upon the load level and power factor, system source and line impedance's, system capacitance to ground and the location of the open circuit. This paper analyses the effect of all electrical quantity to the problem. Based on the test results, the conclusion of mal-operation is drawn.
Research on Online Verification of Relay Protection Setting Value Based on Multi-source Information Fusion Technology and Bow-tie Model

Yan Xu,Rui Chen

DOI: https://doi.org/10.1088/1742-6596/1601/2/022028

2020-07-01

Journal of Physics: Conference Series

Abstract:Abstract In view of the complexity and flexibility of the current power grid, in order to make relay protection online verification more accurate and effective, a protection importance degree sequence assessment method based on the multi-source information fusion technology and bowtie model is proposed. Firstly, the cause of incorrect protection actions is analyzed by establishing a fault tree through multi-source information fusion technology, and the event tree analysis method is used to deduce the final development result of the event. Combined with the fault tree and the event tree, a bow-tie model is formed to visually and completely describe the whole process of the event. Then the economic loss of the event is analyzed as the basis for assessing the protection importance degree, and the online inspection of the protection setting value is completed from high to low according to the importance degree sequence. Finally, the IEEE 3-machine 9-bus system is used to verify the correctness and rationality of the method through simulation.
On-line Operating Risk Assessment of Hidden Failures in Protection System

Wenchuan Wu

2009-01-01

Abstract:Hidden failures in protection system will cause the incorrect action of relay protection and then derogate the power system.From the point of the system control center,the influence of hidden failures of protection relay to power system security was investigated.An operating risk assessment algorithm for hidden failures was developed,which could calculate the conditional probability using event tree method and evaluate the severity of hidden failures.In the proposed method,two main reasons of hidden failures including incorrect relay setting and hardware defect in protection system were both formulated.The operation risk assessment module using the proposed method was tested in a provincial power network in China and proved practical.
Analysis of Microprocessor Based Protective Re-lay's (MBPR) Differential Equation Algorithms

Bruno Osorno

DOI: https://doi.org/10.48550/arXiv.1006.4444

2010-06-23

Abstract:This paper analyses and explains from the systems point of view, microprocessor based protective relay (MBPR) systems with emphasis on differential equation algorithms. Presently, the application of protective relaying in power systems, using MBPR systems, based on the differential equation algorithm is valued more than the protection relaying based on any other type of algorithm, because of advantages in accuracy and implementation. MBPR differential equation approach can tolerate some errors caused by power system abnormality such as DC offset. This paper shows that the algorithm is a system description based and it is immune from distortions such as DC-offset. Differential equation algorithms implemented in MBPR are widely used in the protection of transmission and distribution lines, transformers, buses, motors, etc. The parameters from the system, utilized in these algorithms, are obtained from the power system current i(t) or voltage v(t), which are abnormal values under fault or distortion situations. So, an error study for the algorithm is considered necessary.

Other Computer Science
Research on pilot protection applied in aircraft annular power distribution system

Zhongshan Jiang,Yanping Liu,Bin Wang,Xinzhou Dong,Yan, Wang

DOI: https://doi.org/10.1109/APAP.2011.6180815

2011-01-01

Abstract:In the annular power distribution system, short-circuit fault of bus-bars will do fatal harm to aircraft, and it is necessary to protect the ring-net bus-bars. Protecting bus-bars has to meet the requirements that protection devices do not refuse to operate and backup protection devices do not act incorrectly. This paper builds a model about the annular power distribution system and stimulates the fault system based on MATLAB. According to the fault features, directional blocking pilot protection is put forward. The results prove that the new method can achieve automatic isolation of the bus-bar at fault, ensures the safety of aircraft power distribution system, and it is of great importance to improve the reliability of aircraft power distributing. © 2011 IEEE.

Analysis of maloperation on the REB103 busbar protection

Study on the differential protection of busbar with magnetic restraint

Design of a residual current circuit breaker IC with anti-interference technique

ANALYSIS AND COUNTERMEASURE FOR MISOPERATION OF LONGITUDINAL DIFFERENTIAL PROTECTION WITH UNCLEAR REASON

Maloperation Analysis and Preventive Measures of 500 kV Reactor Protection

Analysis of the Adaptive Scheme of Identifying the Substituting Situation

Adaptive Distance Relay for Preventing Error Action of Reactive Fault

Performance analysis of multiphase compensated distance relay in single-phase-to-ground fault with power swing

Effect of Reactive Equivalent Fault Impedance on Distance Protection

Analysis on Relay Pretection Actions of 7.20 Failure of Xindian Substation

MAGNETIC RESTRAINING DIFFERENTIAL BUS PROTECT

Analysis of a 35kV vacuum circuit breaker accident caused by protection misoperation

Operation Status Monitoring for 500 Kv DC Circuit Breaker with Internal Failures and Relative Backup Fault Isolation Schemes

Analysis of the Maloperation of Transformer Differential Protection after External Fault Removed

Multiphysics Analysis Of The Busbar In Mmc Submodule Under Dc Pole-To-Pole Fault

Study of Rreliability Mmodeling for Rrelay Pprotection Ssystem in Ddigital Ssubstations

Analysis And Simulation To Spurious Operation Of Sensitive Directional Earth Fault Under Load Switching Condition

Research on Online Verification of Relay Protection Setting Value Based on Multi-source Information Fusion Technology and Bow-tie Model

On-line Operating Risk Assessment of Hidden Failures in Protection System

Analysis of Microprocessor Based Protective Re-lay's (MBPR) Differential Equation Algorithms

Research on pilot protection applied in aircraft annular power distribution system