Abstract:Blending type of ABS with different polybutadiene rubber (PB) and polyacrylonitrile (AN) contents in SAN phase is prepared at 240 degrees C to study the effects of PB and AN content on the structure and the properties of DB/ABS blends. Different kinds of productive ABS along with the blend-type ABS are used to compare the properties of PC/ABS and DB/ABS blends comprehensively. All blends are made by melt blending for 10 min with sheer rate of 30 r/min. The result shows that, in DB/Blend-type ABS (70/30) blends, PB content exhibits significant influence on the tensile properties. Samples with 6.3 wt% of PB always show the best performance both in yield strength and elongation at break when AN content is fixed at 18 wt%, 25 wt% and 30 wt%; while increasing AN content in the sample with the same PB content would result in better blends properties even not so obvious as PB content. Scanning electron microscopy gives exactly the same trend for phase morphology with PB and AN contents, revealing best uniform scale of dispersed phase (ABS) among 0.5 - 1.2 mu m at 6.3 wt% of PB. Thermal gravimetric analysis shows that all DB/ABS blends have good thermal stability, which is not obviously affected by PB content and AN content. Single peak of glass transition shows good compatibility in the DB/ABS blends. Excellent compatibility of DB with ABS in the sample is exhibited through dynamic mechanical analysis. The glasstransition temperature of DB/ABS blends are closed to that of DB, mildly affected by PB and AN content. Besides, both blending type ABS and different kinds of productive type ABS are used to compare the properties of DB/ABS blends and traditional bisphenol-A-type PC/ABS blends. Basic laws of tensile properties in DB/ABS remain the same as in PC/ABS blends using different types of ABS.

Effect of rubber contents on brittle–tough transition in acrylonitrile-butadiene-styrene blends

Blending ABS resin and its effect on structure and properties of PC/ABS BLEND alloy

Mechanical and Morphological Properties and Deformation Mechanisms of Acrylonitrile-Butadiene-Styrene/Poly(ϵ-Caprolactone) Blends with Varied Matrix Composition

Influence of the Tert‐dodecyl Mercaptan Content in Poly(acrylonitrile‐butadiene‐styrene) on Properties of Chlorinated Polyvinyl Chloride/poly(acrylonitrile‐butadiene‐styrene) Blends

Abs/蒙脱土纳米复合材料的制备、结构及性能

Effect of Abs Grafting Degree and Compatibilization on the Properties of Pbt/Abs Blends

Compatibilizing and toughening of the styrene and acrylonitrile copolymer and core‐shell impact modifier obtained by agglomerate technologies

Preparation and Mechanical Properties of Toughened ABS Resin via Bulk Polymerization

Toughening Effect of Poly(Ethene-Co-1-Butene)-Graft-Methyl Methacrylate and Acrylonitrile on Styrene-Acrylonitrile Copolymer (San)

Structure and Properties of Isosorbide type Polycarbonate/ABS Blend

Influence of Core-Shell Particles Structure on the Morphology and Brittle-Ductile Transition of Pbt/Abs-G-Gma Blends

Blends of rABS and SEBS: Influence of In-Situ Compatibilization on the Mechanical Properties

Investigation of the Properties of Epoxy-Functionalized Acrylonitrile-butadiene-styrene Toughened Poly (butylene Terephthalate) and Its Blends

Compatibilizing and toughening blends of recycled acrylonitrile-butadiene-styrene/recycled high impact polystyrene blends via styrene-butadiene-glycidyl methacrylate terpolymer

Effect of Maleic Anhydride Copolymerization Mode on the Properties of PA6/ABS Blends

Investigation of the Properties of PBT/ABS-g-GMA Blends Modified with Epoxy Resin of Mid-Molecular Weights

Morphology and mechanical properties of Acrylonitrile-styrene-acrylate toughened plastics with block copolymer chain structure: Acrylonitrile-styrene-acrylate (ASA) toughened plastics with block copolymer chain structure

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Toughening of PBT/PC Blends with Core-Shell Modifier

Properties of Poly(butylene Terephthalate)/bisphenol A Polycarbonate Blends Toughening with Epoxy-Functionalized Acrylonitrile–Butadiene–Styrene Particles

Modification of the Grafting Character to Prepare PA6/ABS-g-MA Blends with Higher Toughness and Stiffness