Abstract:This paper presents a novel seismic isolation floor system that aims to address the issue of incongruent deformation between the floor and the resilient steel frame structure. The proposed study introduces a design methodology for the seismic isolation floor system, along with the consideration of its impact on the resilient beam-column nodes. Subsequently, a scaled-down test model is built and constructed, consisting of three stories with a height of 1.2 m and a 2 × 2 span configuration, in accordance with the aforementioned design methodology. The experimental study involved conducting unidirectional shaking table tests on the model in both horizontal directions. The scaled-down model was subjected to seismic excitations of varying intensities, ranging from an 8-degree multiple-occurrence earthquake to a 9-degree rare-occurrence earthquake. Additionally, an extremely rare-occurrence earthquake with an acceleration of 0.75 g was also applied to the model. The test results indicate that the beam-column node exhibits a maximum opening of 4.56 mm and an angle of rotation of 3.04%. Furthermore, the seismic isolation building system demonstrates the ability to accommodate the "expansion effect" of the resilient structure, while simultaneously maintaining load carrying capacity and effectively transmitting horizontal forces. The seismic isolation floor exhibits a notable reduction of 54.8% in its maximum horizontal inertia force, hence demonstrating a favourable damping effect. Based on the observed alterations in the X-direction frequency of the structure prior to and after to the seismic event with a PGA of 0.07 g, it can be inferred that the beam-column connections inside the structure may be deemed as stiff when subjected to several earthquakes. In the PGA = 0.75 g scenario, the maximum interstory displacement angle of 1/69 is observed in the X direction of the 2nd floor. This value is in close proximity to the elastic-plastic interstory displacement angle of 1/50. However, there is no visible deformation or damage to the structure as a whole, and the strain of each member remains within the elastic range, not exceeding 1675 με. Hence, it is widely acknowledged that the resilient steel frame, equipped with a seismic isolation floor system, exhibits robust post-earthquake functional resilience in the face of unidirectional seismic activity.

One-way shaking table test study of resilient steel frame with seismic isolated floor system

Pseudo-dynamic testing of hybrid frame with steel beams bolted to CFT columns

Seismic Behaviors of High-Strength Bolted End-Plate Connected Composite Steel Beam and Square Concrete Filled Steel Tube Column Frames

Shaking table test of a steel frame structure with layered three‐dimensional isolation

Study on remote collaborative pseudo-dynamic tests of multi-story frames

Large-scale shaking table tests of a six-story floor-by-floor assembled CFS frame-framing shear wall structure

Seismic Isolation Layout Optimized of Mid-Rise Reinforced Concrete Building Frame Structure

Seismic performance of a frame‐supported shear wall over‐track building through shaking table test

The Shaking Table Test on a Prefabricated Integral Frame Shear Wall Structure with a New Prefabricated Floor

Simulation of shake‐table test for a two‐story low‐damage concrete wall building

Shaking Table Tests on the Multi-Dimensional Seismic Response of Long-Span Grid Structure with Base-Isolation

Hybrid geotechnical and structural seismic isolation: Shake table tests

Shaking table tests and numerical analysis of RC coupled shear wall structure with hybrid replaceable coupling beams

Shake table testing and computational investigation of the seismic performance of modularized suspended building systems

Seismic responses analysis of multi-story suspended floors system

Seismic performance evaluation of a novel resilient steel frame with self-centering rocking columns and replaceable energy-dissipating connections for low-rise structures

Shaking table tests of base-isolated reinforced concrete frame by double friction pendulum bearings

A Substructural Shake Table Testing Method for Full-Scale Nonstructural Elements

Investigation on Seismic Performance of Bidirectional Self-Centering Reinforced Concrete Frame Structures by Shaking Table Tests

Horizontal Shaking Table Tests on a Four-Story Prototype Structure Using Multi-Dimensional Earthquake Isolation and Mitigation Devices

Shake Table Tests of a Full-Scale Two-Story Plate-Type Modular Composite Building with Semi-Rigid Corner Connections