KCN Chemical Etching of van der Waals Sb 2 Se 3 Thin Films Synthesized at Low Temperature Leads to Inverted Surface Polarity and Improved Solar Cell Efficiency

Maykel Jiménez-Guerra,Lorenzo Calvo-Barrio,Jose Miguel Asensi,Ivan Caño-Prades,Shunya Yan,Esther Barrena,Joaquim Puigdollers,Zacharie Jehl,Yudania Sánchez,Edgardo Saucedo,Maykel Jiménez-Guerra,Ivan Caño-Prades,Yudania Sánchez

DOI: https://doi.org/10.1021/acsaem.3c01584

IF: 6.4

2024-01-22

ACS Applied Energy Materials

Abstract:Recent developments in Sb2Se3 van der Waals material as an absorber candidate for thin film photovoltaic applications have demonstrated the importance of surface management for improving the conversion efficiency of this technology. Sb2Se3 thin films' versatility in delivering good efficiencies in both superstrate and substrate configurations, coupled with a compatibility with various low-temperature deposition techniques (below 500 °C and often below 350 °C), makes them highly attractive for advanced photovoltaic applications. This study presents a comparative analysis of the most effective chemical etchings developed for related thin film chalcogenide technologies to identify and understand the most appropriate surface chemical treatments for Sb2Se3 in substrate configuration, synthesized using a sequential process at very low temperatures (320 °C). Eight different chemical etchings were tested and investigated, and the results show that only KCN-based solutions lead to an improvement in the solar cell's performance, primarily due to an increase in the fill factor. Surface analysis of the samples shows that KCN etching produces very Sb-rich surfaces that do not affect the properties of the bulk. It is proposed that this Sb-rich interface inverts the surface polarity, creating a "buried junction" with CdS, thereby explaining the improvement of the fill factor of the devices, as confirmed by device modeling. The results of this study underscore the importance of surface management in low-temperature synthesized Sb2Se3 absorbers, where Sb-rich interfaces are crucial for achieving high-efficiency devices. This research contributes to ongoing efforts to improve the performance of Sb2Se3 thin film photovoltaic technology and could pave the way for the development of more efficient solar cells with optimized interfaces.

materials science, multidisciplinary,chemistry, physical,energy & fuels

What problem does this paper attempt to address?

KCN Chemical Etching of van der Waals Sb 2 Se 3 Thin Films Synthesized at Low Temperature Leads to Inverted Surface Polarity and Improved Solar Cell Efficiency

Magnetron Sputtered Sb2Se3-based Thin Films Towards High Performance Quasi-Homojunction Thin Film Solar Cells

Efficient CdS/Sb 2 S 3 interfacial modification using sodium borohydride etching for enhanced performance of low-cost full-inorganic antimony-based solar cells

Towards high efficiency inverted Sb2Se3 thin film solar cells

Solution-processed SnO2 interfacial layer for highly efficient Sb2Se3 thin film solar cells

Quasi-Vertically Oriented Sb 2 Se 3 Thin-Film Solar Cells with Open-Circuit Voltage Exceeding 500 mV Prepared via Close-Space Sublimation and Selenization

Improved Open‐Circuit Voltage of Sb 2 Se 3 Thin‐Film Solar Cells Via Interfacial Sulfur Diffusion‐Induced Gradient Bandgap Engineering

Hydrazine Hydrate‐Induced Surface Modification of CdS Electron Transport Layer Enables 10.30%‐efficient Sb2(S,Se)3 Planar Solar Cells

Thin-Film Solar Cells Based on Selenized CuSbS2 Absorber

Unveiling the Influence of Absorber Thickness on Efficient Sb 2 (S, Se) 3 Solar Cells Through Controlled Chemical Bath Deposition

Optimisation of Sb2S3 thin-film solar cells via Sb2Se3 post-treatment

Sputtered and Selenized Sb2Se3 Thin-Film Solar Cells with Open-Circuit Voltage Exceeding 500 Mv

Interface Formation between CdS and Alkali Postdeposition-Treated Cu(In,Ga)Se2 Thin-Film Solar Cell Absorbers-Key To Understanding the Efficiency Gain

Vapor Transport Deposition of Sb 2 (S,Se) 3 Solar Cells with Continuously Tunable Band Gaps

Microenvironment Created by SnSe2 Vapor and Pre‐Selenization to Stabilize the Surface and Back Contact in Kesterite Solar Cells

High-efficient Sb 2 Se 3 solar cell using Zn x Cd 1- x S n-type layer

Heterostructured CdS Buffer Layer for Sb2Se3 Thin Film Solar Cell

Fabricating High‐Efficiency Sb2(S,Se)3 Solar Cells by Novel Additive‐Assisted Longitudinal Component Engineering

Post-deposition annealing and interfacial ALD buffer layers of Sb$_2$Se$_3$/CdS stacks for reduced interface recombination and increased open-circuit voltages

Optimizing Crystal Orientation and Defect Mitigation in Antimony Selenide Thin-Film Solar Cells through Buffer Layer Energy Band Adjustment

Grain‐Boundary Elimination via Liquid Medium Annealing toward High‐Efficiency Sb2Se3 Solar Cells