Abstract:Antimony chalcogenides are widely studied as a light-absorbing material due to their merits of low toxicity, efficient cost, and excellent photovoltaic properties. However, the band gaps of antimony selenide (approximately 1.1 eV) and antimony sulfide (approximately 1.7 eV) both deviate from the optimal detailed balance band gap (∼1.3 eV) for terrestrial single-junction solar cells. Notably, the band gap of Sb2(S, Se)3 can be tunable in the range from 1.1 to 1.7 eV, which can cover the detailed balance band gap. In this work, the vapor transport deposition method with two independent evaporation sources is used to deposit Sb2(S, Se)3 thin films. By carefully optimizing the evaporation temperature and the start evaporation time of the Sb2Se3 and Sb2S3 sources, a suitable band gap of 1.33 eV is obtained. Finally, on the basis of the optimal Sb2(S, Se)3 films, Sb2(S, Se)3 solar cells without a hole transport layer achieved an efficiency of 7.03%.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c10758.Saturated vapor pressure curves of Sb2Se3 and Sb2S3; temperature–time curves of Sb2Se3 and Sb2S3 sources; top-view SEM images at different Sb2Se3 and Sb2S3 source temperatures; XRD diffraction pattern under different Sb2Se3 and Sb2S3 source temperatures; transmission spectroscopy at different Sb2Se3 and Sb2S3 source temperatures; schematic diagram of thin-film light absorption; heating process of the uniform Sb2(S, Se)3 films and band gaps of Sb2(S, Se)3 films; 1/C2–V curves of the devices; band gaps of the devices obtained from EQE data; J–V curves under different light intensities; atomic and ionic radii; material parameters for SCAPS simulations; CdS trap state parameters for SCAPS simulations; and Sb2(S, Se)3 trap state parameters (PDF)This article has not yet been cited by other publications.

Vapor Transport Deposition of Sb 2 (S,Se) 3 Solar Cells with Continuously Tunable Band Gaps

HTL-Free Sb 2 (S, Se) 3 Solar Cells with an Optimal Detailed Balance Band Gap

Improved Open‐Circuit Voltage of Sb 2 Se 3 Thin‐Film Solar Cells Via Interfacial Sulfur Diffusion‐Induced Gradient Bandgap Engineering

Controllable vapor transport deposition of efficient Sb2(S,Se)3 solar cells via adjusting evaporation source area

Fabricating over 7%-efficient Sb2(S,Se)3 thin-film solar cells by vapor transport deposition using Sb2Se3 and Sb2S3 mixed powders as the evaporation source

Magnetron Sputtered Sb2Se3-based Thin Films Towards High Performance Quasi-Homojunction Thin Film Solar Cells

Se-Elemental Concentration Gradient Regulation for Efficient Sb2(S,Se)3 Solar Cells With High Open-Circuit Voltages

Temperature‐Gradient Solution Deposition Amends Unfavorable Band Structure of Sb2(S,Se)3 Film for Highly Efficient Solar Cells

Bandgap grading via sputtering and post-selenization using SeS2 powder enabling Sb2(S,Se)3 solar cells with 7.1% efficiency

Solvent‐Assisted Hydrothermal Deposition Approach for Highly‐Efficient Sb2(S,Se)3 Thin‐Film Solar Cells

Investigation of electronic transport mechanisms in Sb2Se3 thin-film solar cells

Sputtered and Selenized Sb2Se3 Thin-Film Solar Cells with Open-Circuit Voltage Exceeding 500 Mv

Oxygen Content Modulation Toward Highly Efficient Sb2Se3 Solar Cells

Heterogeneous Nucleation Regulation Amends Unfavorable Crystallization Orientation and Defect Features of Antimony Selenosulfide Film for High‐Efficient Planar Solar Cells

Hydrazine solution processed Sb2S3, Sb2Se3 and Sb2(S(1-x)Se(x))3 film: molecular precursor identification, film fabrication and band gap tuning

Highly Efficient and Stable Planar Heterojunction Solar Cell Based on Sputtered and Post-Selenized Sb 2 Se 3 Thin Film

An Optimization Path for Sb2(S,Se)3 Solar Cells to Achieve an Efficiency Exceeding 20

Thermal evaporation–deposited hexagonal CdS buffer layer with improved quality, enlarged band gap, and reduced band gap offset to boost performance of Sb2(S,Se)3 solar cells

All‐Vacuum‐Processed Sb2(S,Se)3 Thin Film Photovoltaic Devices via Controllable Tuning Seed Orientation (Adv. Funct. Mater. 22/2023)

The Impact of Ga and S Concentration and Gradient in Cu(In,Ga)(Se,S)2 Solar Cells

Sb2Se3 thin film solar cells in substrate configuration and the back contact selenization