Abstract:Full-area passivating contacts based on SiOx/poly-Si stacks are key for the new generation of industrial silicon solar cells substituting the passivated emitter and rear cell (PERC) technology. Demonstrating a potential efficiency increase of 1 to 2% compared to PERC, the utilization of n-type wafers with an n-type contact at the back and a p-type diffused boron emitter has become the industry standard in 2024. In this work, variations of this technology are explored, considering p-type passivating contacts on p-type Si wafers formed via a rapid thermal processing (RTP) step. These contacts could be useful in conjunction with n-type contacts for realizing solar cells with passivating contacts on both sides. Here, a particular focus is set on investigating the influence of the applied thermal treatment on the interfacial silicon oxide (SiOx) layer. Thin SiOx layers formed via ultraviolet (UV)-O3 exposure are compared with layers obtained through a plasma treatment with nitrous oxide (N2O). This process is performed in the same plasma enhanced chemical vapor deposition (PECVD) chamber used to grow the Si-based passivating layer, resulting in a streamlined process flow. For both oxide types, the influence of the RTP thermal budget on passivation quality and contact resistivity is investigated. Whereas the UV-O3 oxide shows a pronounced degradation when using high thermal budget annealing (T > 860 °C), the N2O-plasma oxide exhibits instead an excellent passivation quality under these conditions. Simultaneously, the contact resistivity achieved with the N2O-plasma oxide layer is comparable to that yielded by UV-O3-grown oxides. To unravel the mechanisms behind the improved performance obtained with the N2O-plasma oxide at high thermal budget, characterization by high-resolution (scanning) transmission electron microscopy (HR-(S)TEM), X-ray reflectometry (XRR) and X-ray photoelectron spectroscopy (XPS) is conducted on layer stacks featuring both N2O and UV-O3 oxides after RTP. A breakup of the UV-O3 oxide at high thermal budget is observed, whereas the N2O oxide is found to maintain its structural integrity along the interface. Furthermore, chemical analysis reveals that the N2O oxide is richer in oxygen and contains a higher amount of nitrogen compared to the UV-O3 oxide. These distinguishing characteristics can be directly linked to the enhanced stability exhibited by the N2O oxide under higher annealing temperatures and extended dwell times.

Wet-Chemically Grown Interfacial Oxide for Passivating Contacts Fabricated With an Industrial Inline Processing System

Plasma enhanced chemical vapor‐deposited SiOx(Ny)/n‐type polysilicon on oxide passivating contacts in industrial back‐contacted Si solar cells

Development and Characterization of N2O-Plasma Oxide Layers for High-Temperature p-Type Passivating Contacts in Silicon Solar Cells

Application of SiO2 Passivation Technique in Mass Production of Silicon Solar Cells

Polysilicon Passivating Contacts for Silicon Solar Cells: Interface Passivation and Carrier Transport Mechanism

Ultrathin silicon oxide prepared by in-line plasma-assisted N2O oxidation (PANO) and the application for n-type polysilicon passivated contact

Interfacial Engineering of Cu 2 O Passivating Contact for Efficient Crystalline Silicon Solar Cells with an Al 2 O 3 Passivation Layer

UV-Ozone Oxide layer for Junction Passivation and Passivating Contact Process of Silicon Solar Cells

Industrial High Throughput Emitter Formation and Thermal Oxidation for Silicon Solar Cells by the High Temperature Stack Oxidation Approach

24.2% efficient POLO back junction solar cell with an AlOx/SiNy dielectric stack from an industrial‐scale direct plasma‐enhanced chemical vapor deposition system

High‐Performance and Industrially Viable Nanostructured SiO x Layers for Interface Passivation in Thin Film Solar Cells

Plasma Treatment for Chemical SiOx Enables Excellent Passivation of P-Type Polysilicon Passivating Contact Featuring the Lowest J0 Of-6 Fa/cm2

Phosphorus-diffused polysilicon contacts for solar cells

SiO2 Passivation Layer Grown by Liquid Phase Deposition for Silicon Solar Cell Application

Simulation-based roadmap for the integration of poly-silicon on oxide contacts into screen-printed crystalline silicon solar cells

Design and Optimization of SiOx/AZO Transparent Passivating Contacts for High‐Efficiency Crystalline Silicon Solar Cells

Tunnel oxide passivated contacts formed by ion implantation for applications in silicon solar cells

A silicon oxide-based highly transparent passivating contact for crystalline silicon solar cells approaching efficiencies of 23%

N-type polysilicon passivating contacts using ultra-thin PECVD silicon oxynitrides as the interfacial layer

Plasma treatment for chemical SiOx enables excellent passivation of p-type polysilicon passivating contact featuring the lowest J of ∼6 fA/cm2

Improved Surface Passivation by Wet Texturing, Ozone‐Based Cleaning, and Plasma‐Enhanced Chemical Vapor Deposition Processes for High‐Efficiency Silicon Heterojunction Solar Cells