Abstract:Cylindrical microlens arrays (CMLAs) play a key role in many optoelectronic devices, and 100% fill-factor CMLAs also have the advantage of improving the signal-to-noise ratio and avoiding stray-light effects. However, the existing preparation technologies are complicated and costly, which are not suitable for mass production. Herein, we propose a simple, efficient, and low-cost manufacturing method for CMLAs with a high fill-factor via the electric-field-driven (EFD) microscale 3D printing of polydimethylsiloxane (PDMS). By adjusting the printing parameters, the profile and the fill-factor of the CMLAs can be controlled to improve their optical performance. The optical performance test results show that the printed PDMS CMLAs have good image-projecting and light-diffraction properties. Using the two printing modes of this EFD microscale 3D-printing technology, a cylindrical dual-microlens array with a double-focusing function is simply prepared. At the same time, we print a series of specially shaped microlenses, proving the flexible manufacturing capabilities of this technology. The results show that the prepared CMLAs have good morphology and optical properties. The proposed method may provide a viable route for manufacturing large-area CMLAs with 100% fill-factor in a very simple, efficient, and low-cost manner.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c08652.EFD microscale 3D-printing principle and two printing modes; microfluidic chip structure and mixing effect verification; comparison of nanoimprint results of different hybrid methods of PDMS; effect of the nozzle size on the printing line width and height; effect of the printing height on the printing line width and height; schematic diagram of the imaging experiment of the PDMS CMLA; schematic diagram of the imaging experiment of the PDMS CMLA; and comparison of CMLAs manufactured by various technologies (PDF)High-speed photography of the micro-extrusion printing mode (MP4)Printing CMLAs with 100% fill-factor using the micro-extrusion mode (MP4)High-speed photography of the continuous cone jet printing mode (MP4)Printing CMLAs with 100% fill-factor using a continuous cone jet mode (MP4)Printing cylindrical dual-MLAs via two printing modes of EFD microscale 3D printing (MP4)Printing phoenix-shaped specially shaped microlenses by the continuous cone jet mode (MP4)Printing phoenix-shaped specially shaped microlenses by the microextrusion mode (MP4)This article has not yet been cited by other publications.

Rapid fabrication of large-area concave microlens arrays on PDMS by a femtosecond laser

Convex Silica Microlens Arrays Via Femtosecond Laser Writing.

Rapid fabrication of quasi-periodic aspherical concave microlens array with different focal lengths on fused silica by shaping picosecond laser-induced multi-step wet-etching for multi-layer optical imaging

Optical Nanofabrication of Concave Microlens Arrays

Single-pulse Writing of a Concave Microlens Array.

Toward On-Chip Unidirectional and Single-Mode Polymer Microlaser

Rapid Fabrication Of Continuous Surface Fresnel Microlens Array By Femtosecond Laser Focal Field Engineering

Wet-etching-assisted femtosecond laser holographic processing of a sapphire concave microlens array.

Rapid Fabrication of Large-Area Concave Microlens Array on ZnSe

Fabrication of large-area microwells on Polydimethylsiloxane films by femtosecond laser ablation

Fabrication of Large-Area Silicon Spherical Microlens Arrays by Thermal Reflow and ICP Etching

Progress In Femtosecond Laser Fabrication Of Microlens Array With Spatial Light Modulators

Fast Fabrication of Large-Area Two-Dimensional Micro/Nanostructure by Femtosecond Laser

3D Printing of a PDMS Cylindrical Microlens Array with 100% Fill-Factor

Variable focus convex microlens array on K9 glass substrate based on femtosecond laser processing and hot embossing lithography

Fabrication of a diamond concave microlens array for laser beam homogenization

Rapid Fabrication of Smooth Micro-Optical Components on Glass by Etching-Assisted Femtosecond Laser Modification

Microlens arrays prepared via colloidal microsphere templating

An Ultraviolet-Lithography-Assisted Sintering Method for Glass Microlens Array Fabrication

Rapid manufacture of defect-free microlens arrays by precision glass molding

100% Fill-Factor Aspheric Microlens Arrays (AMLA) with Sub-20-nm Precision