Abstract:Carbon nanotube field-effect transistors (CNT FETs) have been demonstrated to exhibit high performance only through low-temperature fabrication process and require a low thermal budget to construct monolithic three-dimensional (M3D) integrated circuits (ICs), which have been considered a promising technology to meet the demands of high-bandwidth computing and fully functional integration. However, the lack of high-quality CNT materials at the upper layer and a low-parasitic interlayer dielectric (ILD) makes the reported M3D CNT FETs and ICs unable to provide the predicted high performance. In this work, we demonstrate a multilayer stackable process for M3D integration of high-performance aligned carbon nanotube (A-CNT) transistors and ICs. A low-kappa (similar to 3) interlayer SiO2 layer is prepared from spin-on-glass (SOG) through processes with a highest temperature of 220 C-degrees, presenting low parasitic capacitance between two transistor layers and excellent planarization to offer an ideal surface for the A-CNT and device fabrication process. A high-quality A-CNT film with a carrier mobility of 650 cm(2) V-1 s(-1) is prepared on the ILD layer through a clean transfer process, enabling the upper CNT FETs fabricated with a low-temperature process to exhibit high on-state current (1 mA mu m(-1)) and peak transconductance (0.98 mS mu m(-1)). The bottom A-CNT FETs maintain pristine high performance after undergoing the ILD growth and upper FET fabrication. As a result, 5-stage ring oscillators utilizing the M3D architecture show a gate propagation delay of 17 ps and an active region of approximately 100 mu m(2), representing the fastest and the most compact M3D ICs to date.

FDSOI Process Based MIV-transistor Utilization for Standard Cell Designs in Monolithic 3D Integration

Modeling and Design of Dual-Purpose MIV in Monolithic 3D IC

Efficient and Scalable MIV-transistor with Extended Gate in Monolithic 3D Integration

Monolithic Three‐dimensional Integration of Aligned Carbon Nanotube Transistors for High‐performance Integrated Circuits

&Amp;#x0022;green&#x0022; On-chip Inductors in Three-Dimensional Integrated Circuits

Metal Inter-layer Via Keep-out-zone in M3D IC: A Critical Process-aware Design Consideration

Mono3D: Open Source Cell Library for Monolithic 3-D Integrated Circuits.

Comprehensive Physical Design Flow Incorporating 3D Connections for Monolithic 3D ICs

Monolithic three-dimensional integration of complementary two-dimensional field-effect transistors

Mono 3 D to Develop Large-Scale Monolithic 3 D Integrated Circuits

Design-Technology Co-Optimization for Stacked Nanosheet Oxide Channel Transistors in Monolithic 3D Integrated Circuit Design

Monolithic 3D Integration of Vertically Stacked CMOS Devices and Circuits with High-Mobility Atomic-Layer-Deposited In2O3 N-Fet and Polycrystalline Si P-Fet: Achieving Large Noise Margin and High Voltage Gain of 134 V/V

Single Event Induced Crosstalk of Monolithic 3D Circuits Based on a 22 nm FD-SOI Technology

Open Source Cell Library Mono3D to Develop Large-Scale Monolithic 3D Integrated Circuits.

Monolithic-3D Integration with 2D Materials: Toward Ultimate Vertically-Scaled 3D-ICs

Monolithic 3D integration of back-end compatible 2D material FET on Si FinFET

Redundant Vias Insertion for Performance Enhancement in 3D ICs.

Heterogeneous Monolithic 3-D IC Designs: Challenges, EDA Solutions, and Power, Performance, Cost Tradeoffs

A Proposal of Vertical MOSFET and Electrothermal Analysis for Monolithic 3-D ICs

Area efficient layout design of CMOS circuit for high-density ICs

From Flip FET to Flip 3D Integration (F3D): Maximizing the Scaling Potential of Wafer Both Sides Beyond Conventional 3D Integration