Abstract:Solution acidity greatly affects the fabrication of high-performance oxide dispersion-strengthened tungsten (ODS-W) alloys by liquid-liquid doping. In the present study, yttria-stabilised zirconia (Zr(Y)O2)-strengthened tungsten alloys (W-Zr(Y)O2) were developed via azeotropic distillation. The effect of solution pH on the precursor morphology and microstructure and the mechanical properties of the corresponding alloys was investigated. When the solution pH increased from 2 to 8, a larger number of bonding Zr(Y)O2 particles could be observed in the alloys. The W-Zr(Y)O2 alloy fabricated with the pH 2 precursor powder exhibited a better microstructure and mechanical properties (relative density, micro-hardness, yield, and ultimate strength) than the alloys prepared with pH 5 and 8 precursor powders. The ultimate compressive strength and failure strain of the pH 2 alloy were 1009 MPa and 0.22, respectively. In addition, this alloy contained finer particles than the pH 5 and 8 alloys. The grain sizes of W-Zr(Y)O2 alloys fabricated with pH 2, 5, and 8 precursor powders were in the range of 2–6 μm, which implies that they were much smaller than the particles in pure tungsten. Due to a complicated abrasion mechanism, the wear resistance of the W-Zr(Y)O2 alloys initially increased and then decreased with an increase in the Zr(Y)O2 content. Finally, we could confirm that the alloy fabricated with the pH 2 precursor powder (with 3.0 wt.% Zr(Y)O2) exhibited the most optimal chemical composition, microstructure, and compressive properties. In addition, the wear resistance of the W-Zr(Y)O2 alloy fabricated with the pH 2 precursor powder was characterised. Finally, we expect that the results outlined in this study will act as basic guidelines for the fabrication of ODS-W alloys by liquid-liquid doping.

Anisotropy and stability of the mechanical properties of the W alloy plate reinforced with Y-Zr-O particles and prepared by a wet chemical method

Tensile fracture behavior and texture evolution of a hot-rolled W-Y<sub>2</sub>(Zr)O<sub>3</sub> alloy

Tensile fracture behavior and texture evolution of a hot-rolled W–Y2(Zr)O3 alloy

Extremely uniform nanosized oxide particles dispersion strengthened tungsten alloy with high tensile and compressive strengths fabricated involving liquid-liquid method

DBTT and tensile properties of as-sintered tungsten alloys reinforced by yttrium-zirconium oxide

High Thermal Shock Resistance of the Hot Rolled and Swaged Bulk W–ZrC Alloys

Fabrication and Stability of Ultrafine ZrC Nanoparticles Dispersion Strengthened Sub-Micrometer Grained W Alloy

Mechanical Properties and Thermal Stability of W-ZrC/HfC-Re Alloys Fabricated by Spark Plasma Sintering

Effect of W-phase on the Mechanical Properties of As-Cast Mg–Zn–Y–Zr Alloys

Effects of ZrC Content on the Mechanical Properties and Microstructures of Hot-Rolled W–ZrC Composites

A study on the effect of solution acidity on the microstructure, mechanical, and wear properties of tungsten alloys reinforced by yttria-stabilised zirconia particles

Effect of rotary swaging and subsequent annealing on microstructure and mechanical properties of W-1.5ZrO2 alloys

Effect of different crystal forms of ZrO 2 on the microstructure and properties of tungsten alloys

Microstructure and Mechanical Properties of Mg–2.0Gd–1.2Y–1.0Zn–0.2Zr Alloy

Compressive mechanical properties of W-particle/Zr-based amorphous alloy composites

Enhanced Mechanical Properties and Thermal Stability of Hot-Rolled Mo-0.5%ZrC Alloy

The Influence of Element Y on the Mechanical Properties of the As-Extruded Mg–Zn–Y–Zr Alloys

Improving Tension/Compression Asymmetry of a Hot‐Extruded Mg–Zn–Y–Zr Alloy Via Yttrium Addition

Effect of Microstructure and Texture on the Mechanical Properties of the As-Extruded Mg–Zn–Y–Zr Alloys

Microstructure evolution of W-1.0 m-ZrO2 alloy during high temperature deformation

Enhancing Strength-Ductility Synergy and Corrosion Residual Strength of Hot-Rolled Mg-2Zn-0.85Y Alloy