Abstract:The thermal stability of an yttria particle dispersion strengthening tungsten (W-2vol%Y2O3) plate with 67 % rolling thickness reduction (WY67) fabricated by powder metallurgy and warm rolling is investigated through isochronous annealing and isothermal annealing. Hardness testing of annealed specimens allows tracking the degradation of the mechanical properties and electron backscatter diffraction (EBSD) was used to characterize the corresponding microstructure. Isochronous annealing for 1 hour between 1150 °C and 1450 °C indicates that the recrystallization temperature of WY67 is about 1400 °C. Herein, the recovery kinetics, recrystallization kinetics, and the evolution of microstructure and texture of WY67 during isothermal annealing at temperatures ranging from 1300 ℃ to 1450 ℃ were investigated in detail. The effect of both the heterogeneity of the deformed microstructure and the yttria particles on the recovery and recrystallization was further studied. The results show that the stored energy of the deformed grains of yttria dispersion strengthened tungsten is texture-dependent and the grain with γ-fiber (normal direction // <111>) texture has the largest stored energy of 546 KJ/m3. The grains with higher stored energy are conducive to recrystallized nucleus/grain growth rather than nucleation during subsequent annealing. The recrystallized texture inherits the deformed texture and is mainly composed of γ-fiber texture. There are more pre-existing potential recrystallization nuclei in the elongated grains with larger deformation in the as-rolled microstructure. Micron-sized yttria particles can stimulate the formation of recrystallization nuclei through particle-stimulated nucleation mechanism, nevertheless, this is not the dominant nucleation mode for WY67 during recrystallization in this study. Fine (submicron) yttria particles hinder the recovery and recrystallization processes through the Smith–Zener pinning effect.

Annealing Characteristics and Mechanism Interpretation of High-Performance Swaged W-Y2O3 Alloy

Research on annealing process for welded joint of the dissimilar steel——weld property and holding time

Mechanical Properties and Thermal Shock Performance of W-Y2O3composite Prepared by High-Energy-rate Forging

Effect of rotary swaging and subsequent annealing on microstructure and mechanical properties of W-1.5ZrO2 alloys

High Strength and Tackling Structural Relaxation by Sub-Grains Synergistic Deformation in W-Re Alloy

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

Restoration kinetics and microstructural evolution of moderately warm-rolled yttria dispersion-strengthened tungsten plate during annealing at high temperatures

Establishment of processing map, microstructure and high-temperature tensile properties of W-0.25 wt% Al2O3 alloys

Evolution of Microstructure and Mechanical Properties of Warm-Rolled W10Re Alloy During Annealing at 1500 °C

Tensile fracture behavior and texture evolution of a hot-rolled W–Y2(Zr)O3 alloy

Room temperature ductile W-Y2O3 alloy with high thermal shock resistance

Effects of annealing on periodic microstructure and mechanical properties of inter-layer hammering hybrid wire arc additively manufactured aluminum alloy

Evolution of microstructure and texture in a warm-rolled yttria dispersion-strengthened tungsten plate during annealing in the temperature range between 1200 °C and 1350 °C

Microstructure Evolution and Mechanical Properties of Ultra-Fine Grain AlCrFe2Ni2Wx High-Entropy Alloys

Tensile fracture behavior and texture evolution of a hot-rolled W-Y<sub>2</sub>(Zr)O<sub>3</sub> alloy

Evolution of microstructure and texture of moderately warm-rolled pure tungsten during annealing at 1300 °C

Anisotropy and stability of the mechanical properties of the W alloy plate reinforced with Y-Zr-O particles and prepared by a wet chemical method

Microstructures and properties of nanocrystalline W-based alloys produced by resistance sintering under ultrahigh pressure

A comparative study on the microstructure and performance stability of Cu-Al2O3 and Cu-Y2O3 alloys after high-temperature annealing

Effects of deformation and annealing on the microstructures and properties of a nonequiatomic Co29Cr29Fe29Ni12.5W0.5 high-entropy alloy

Affecting Structure Characteristics of Rotary Swaged Tungsten Heavy Alloy Via Variable Deformation Temperature