Abstract:The thermal stability of an yttria particle dispersion strengthening tungsten (W-2vol%Y2O3) plate with 67 % rolling thickness reduction (WY67) fabricated by powder metallurgy and warm rolling is investigated through isochronous annealing and isothermal annealing. Hardness testing of annealed specimens allows tracking the degradation of the mechanical properties and electron backscatter diffraction (EBSD) was used to characterize the corresponding microstructure. Isochronous annealing for 1 hour between 1150 °C and 1450 °C indicates that the recrystallization temperature of WY67 is about 1400 °C. Herein, the recovery kinetics, recrystallization kinetics, and the evolution of microstructure and texture of WY67 during isothermal annealing at temperatures ranging from 1300 ℃ to 1450 ℃ were investigated in detail. The effect of both the heterogeneity of the deformed microstructure and the yttria particles on the recovery and recrystallization was further studied. The results show that the stored energy of the deformed grains of yttria dispersion strengthened tungsten is texture-dependent and the grain with γ-fiber (normal direction // <111>) texture has the largest stored energy of 546 KJ/m3. The grains with higher stored energy are conducive to recrystallized nucleus/grain growth rather than nucleation during subsequent annealing. The recrystallized texture inherits the deformed texture and is mainly composed of γ-fiber texture. There are more pre-existing potential recrystallization nuclei in the elongated grains with larger deformation in the as-rolled microstructure. Micron-sized yttria particles can stimulate the formation of recrystallization nuclei through particle-stimulated nucleation mechanism, nevertheless, this is not the dominant nucleation mode for WY67 during recrystallization in this study. Fine (submicron) yttria particles hinder the recovery and recrystallization processes through the Smith–Zener pinning effect.

Restoration kinetics and microstructural evolution of moderately warm-rolled yttria dispersion-strengthened tungsten plate during annealing at high temperatures

Evolution of microstructure and texture in a warm-rolled yttria dispersion-strengthened tungsten plate during annealing in the temperature range between 1200 °C and 1350 °C

Recrystallization Kinetics of Larger Yttria Particle Dispersion Tungsten Alloy Warm Rolled to 50% Thickness Reduction

Mechanical Properties and Thermal Shock Performance of W-Y2O3composite Prepared by High-Energy-rate Forging

Inhomogeneous Deformation Substructure and Its Effect on the Recrystallization Behavior of Yttria Dispersion-Strengthened Tungsten Plate

Microstructure and Annealing Behavior of Three Rolled Pure Tungsten Plates with Different Thickness Reduction

Recrystallization Kinetics of 50% Hot-Rolled 2% Y2O3 Dispersed Tungsten

Evolution of microstructure and texture of moderately warm-rolled pure tungsten during annealing at 1300 °C

Recrystallization behavior of pure tungsten hot-rolled with high accumulated strain during annealing at 1250 C-1350 C

Recrystallization behavior of pure tungsten with different rolling ratio during isothermal annealing at temperature range of 1250-1350 ℃

Microstructure Evolution and Recrystallization after Annealing of Tungsten Heavy Alloy Subjected to Severe Plastic Deformation

Effects of Thickness Reduction on Recrystallization Process of Warm-Rolled Pure Tungsten Plates at 1350 °C

Hardness Loss and Microstructure Evolution of 90% Hot-Rolled Pure Tungsten at 1200–1350 °C

Microstructure and Hardness Evolution During Isothermal Process at 700 °C for Fe–24Mn–0.7Si–1.0Al TWIP Steel

Annealing Characteristics and Mechanism Interpretation of High-Performance Swaged W-Y2O3 Alloy

Thermal Shock Resistance of Nanocrystalline and Ultrafine-Grained W-Y2O3-Ti Alloys

Tensile fracture behavior and texture evolution of a hot-rolled W–Y2(Zr)O3 alloy

Tensile fracture behavior and texture evolution of a hot-rolled W-Y<sub>2</sub>(Zr)O<sub>3</sub> alloy

Microstructure evolution of the rolled tungsten during the current-assisted annealing treatment

Evolution of Microstructure and Mechanical Properties of Warm-Rolled W10Re Alloy During Annealing at 1500 °C

Microstructure and Texture Transformation of Unidirectional Rolled 3% Y2O3p/ZGK200 Composites During Annealing