Abstract:In this paper, fully dense Si3N4/SiC nano-composites were fabricated through polymer-derived ceramics (PDCs) method and spark plasma sintering technique. Polymer-derived SiAlCN ceramic was synthesized by using polysilazane as preceramic precursor, aluminum tri-sec-butoxide as Al source. Then Si3N4/SiC composites with nanometer sized Si3N4 and SiC phases were formed spontaneously during spark plasma sintering through in-situ phase separation of amorphous SiAlCN ceramics. It's found that with the increasement of Al contents, the densification rate was accelerated significantly and serious degradation of Si3N4 phase was avoided by restricting carbothermal reaction. At the same time, Al contained composites show excellent oxidation/corrosion resistance at 1350 °C and 50% H2O - 50% O2 water vapor environment than that of Al free samples. The Si3N4/SiC composites derived from Al contained PDCs overcomes the trade-off between abnormal grain growth and serious degradation of Si3N4 phase, which is a very tough problem for traditional PDC route (without Al) to fabricate Si3N4/SiC composites. For traditional PDC route, (I) if with traditional sintering additives, abnormal grain growth occurs, nano grains cannot be achieved; (II) if without traditional sintering additives, serious degradation of Si3N4 occurs, Si3N4 and SiC composite cannot be formed. Therefore, Al contained polymer-derived ceramics route opens a promising avenue to fabricate Si3N4/SiC nano-composites with fine grain size, uniform microstructure and excellent oxidation/corrosion resistance.

Fabrication of Al 2 O 3 – Ni – CNTs nanocomposites by co-precipitation of CNTs and Ni nanoparticle on Al 2 O 3 powder and spark plasma sintering

Synthesis of uniformly dispersed carbon nanotube reinforcement in Al powder for preparing reinforced Al composites

Fabrication and Characterization of In-Situ Grown Carbon Nanotubes Reinforced SiC/SiC Composite

In-situ Homogeneous Synthesis of Carbon Nanotubes on Aluminum Matrix and Properties of Their Composites

Fabrication and mechanical properties of multi-walled carbon nanotubes doped AlN ceramics prepared by spark plasma sintering

Synthesis Of Carbon Nanotubes By Fine Ni Particles In Ni3al Foam

Sintering Behaviors of Carbon NanotubesAluminum Composite Powders

High Strength and High Ductility in Nickel Matrix Nanocomposites Reinforced by Carbon Nanotubes and Onion-Like-carbon Hybrid Reinforcements

In Situ Synthesis of Ti2AlC–Al2O3/TiAl Composite by Vacuum Sintering Mechanically Alloyed TiAl Powder Coated with CNTs

Fabrication of Carbon Nanotube Reinforced Al Composites with Well-Balanced Strength and Ductility

Mechanical Alloying and Spark Plasma Sintering of Ni-Al-Ti-B Powders for Fabricating Nanocrystailine (Tib+tib2)/ni-3(Al, Ti) Composite

In situ formation of Si3N4–SiC nanocomposites through polymer-derived SiAlCN ceramics and spark plasma sintering

CNTs/Cu-Ti Composites Fabrication Through the Synergistic Reinforcement of CNTs and in Situ Generated Nano-Tic Particles

A Novel Preparation and Properties of In-Situ Grown Carbon Nanotube Reinforced Carbon/carbon Composites

In situ synthesis of nanodiamond reinforced Fe-Ni matrix composites and their properties

Fabrication of CNT/Cu Based Composite with Twice In-Situ Formation from Powder Preparation to Sintering

Two Birds with One Stone: Simultaneous Fabrication of HfC Nanowires and CNTs Through Efficient Utilization of Polymer-Derived Ceramics

Fabrication and properties of CNTS/AlN ceramics

Synthesis of Carbon Nanotube Reinforced Al Matrix Composites Via Cold Spray Deposition

A Novel Processing Route to Develop Alumina Matrix Nanocompositesreinforced with Multi-Walled Carbon Nanotubes

Fabrication of Ni@SiC Composite Nanofibers by Electrospinning and Autocatalytic Electroless Plating Techniques