Abstract:In recent times, auxetic woven structures gained considerable attention from the researchers due to their excellent impact properties in high-performance areas. Researchers have done much work on the auxetic behavior of the natural and low-performance yarns in two-dimensional structures. Keeping in view the structural application of auxetic structures, in this work, three-dimensional (3D) woven auxetic fabrics were developed on conventional weaving machines with high-performance yarns. Effect of high-performance yarns (Para-aramid and UHMWPE) as the main structure and binding threads on the auxeticity of 3D fabric structures and the impact properties of their corresponding composites were discussed. For this purpose, eight different orthogonal 3D woven structures were produced with para-aramid filament yarn as warp and weft, whereas ultra-high molecular weight polyethylene (UHMWPE) filament yarn was used as a binder. The tensile load was applied to the 3D fabrics to check their auxeticity, and a change in thickness was recorded. The results showed that as the float length of binder yarn and warp yarn increases with the equal and same ratio, the auxeticity also increases. While auxeticity decreases as the difference between the float length of binder yarn and warp yarn increases. The Negative Poisson's Ratio (NPR) of 3D woven fabrics ranged from −0.9 to −2.98. In the second step, these 3D woven fabrics were fabricated into their composites using unsaturated polyester resin, and the hand-layup technique. Their impact strength was measured using the Charpy test method. Auxetic woven composites made of high-performance yarns structures showed impact strength ranging from 55.64 kJ/m2 to 158.46 kJ/m2. High-performance yarns (Para-aramid and Ultra-high molecular weight polyethylene) were used to create eight 3D woven and composite samples with enhanced auxetic behavior.The result shows that samples having maximum binding yarn float length and fewer intersection points show maximum auxeticity and increased energy absorption.The maximum auxeticity and impact energy absorption obtained was -2.98 and 158.46 kJ/m2, respectively.The current research has applications in protective textiles and bulletproof composite panels.

Design and Development of 2D Woven Auxetic Fabric and Composites Based on Wave Form Geometry

Geometric Analysis of Three-Dimensional Woven Fabric with in-Plane Auxetic Behavior

3D woven auxetic composites using onloom shaped reinforcement

Development of 3D auxetic structures using para-aramid and ultra-high molecular weight polyethylene yarns

Finite element analysis study of parameters influencing the Poisson's ratio of auxetic woven fabrics

Effect of structural parameters on formability of auxetic weft-knitted fabrics based on zigzag structure

Study on the Tensile Behavior of Helical Auxetic Yarns with Finite Element Method

Development of uni-stretch woven fabrics with zero and negative Poisson’s ratio

Design, Development, and Characterization of Advanced Textile Structural Hollow Composites

In situ energy absorption and negative Poisson's ratio behaviors of 3D weft knitted auxetic fabrics under variant measurements

Mechanical analysis of the auxetic behavior of novel braided tubular structures by the finite element method

ABC‐Auxetics: An Implicit Design Approach for Negative Poisson's Ratio Materials

In-Plane Behavior of Auxetic Non-Woven Fabric Based on Rotating Square Unit Geometry under Tensile Load

Finite element simulation of an auxetic plied yarn structure

Energy absorption from composite reinforced with high performance auxetic textile structure

Recent Advances in Wearable Electromechanical Sensors Based on Auxetic Textiles

A study of tubular braided structure with negative Poisson’s ratio behavior

Mechanical modeling of an auxetic tubular braided structure: Experimental and numerical analyses

Multifunctional auxetic and honeycomb composites made of 3D woven carbon fibre preforms

Creating three-dimensional (3D) fiber networks with out-of-plane auxetic behavior over large deformations

In Situ X‐Ray Tomography of Sintered Metal Fiber Felts Exhibiting Auxetic Effect under Tension and Compression