Abstract:In order to solve the problem of shield hobbing cutter failure due to bias wear and chipping during tunnel boring, TiC-WC/Ni60 coating was prepared on the surface of H13 steel to improve the wear resistance of shield hobbing cutter. In this paper, four kinds of WC-TiC/Ni60 composite coatings with different content ratios of 5 wt% TiC+25 wt% WC, 10 wt% TiC+20 wt% WC, 15 wt% TiC+15 wt% WC and 20 wt% TiC+10 wt% WC were prepared on the surface of H13 steel by using the coaxial powder-feeding laser cladding equipment. The micromorphology, phase, hardness and friction and wear properties were fully studied. The results show that cross-sectional organization of the fused cladding layer mainly consists of columnar crystals, cytocrystals and equiaxial crystals; the hard phases in the fused cladding layer mainly consist of TiWC 2 , Cr 4 Ni 5 W, and Cr 3 C 2 , and so on; The microhardness of the cross-section of the fused cladding layer shows a trend of decreasing at first, then increasing and finally decreasing, and the highest hardness of the fused cladding layer occurs at the subsurface of the fused cladding layer; the friction coefficient of the fused cladding layer shows a trend of decreasing first and then increasing; the wear volume of the fused cladding layer is significantly lower than that of the substrate, and the wear volume of the 15 wt% TiC coating is the smallest of 1.313 mm 3 , which is 86.9 % lower than that of the substrate; the wear mechanism of the substrate is mainly abrasive wear and adhesive wear, and the wear mechanism of the fused cladding layer is mainly brittle spalling, abrasive wear and oxidative wear. The analysis of the experimental results shows that the surface properties of the coating are best when both TiC and WC contents are 15 wt%.

Effect of TiFe/Cr3C2 precursor powder ratio in in-situ synthesis of TiC-reinforced Stellite 6 coatings by PTA cladding

Microstructure and wear resistance of in-situ TiC reinforced Stellite 6 coating using PTA cladding

Effect of TiC addition on the microstructure and properties of laser cladding Ni60A coatings on H13 steel surface

High-temperature wear and cyclic oxidation behavior of (Ti, W)C reinforced stainless steel coating deposited by PTA on a plain carbon steel

Effects of Aluminum Addition on Microstructure and Properties of TiC-TiB2/Fe Coatings In Situ Synthesized by TIG Cladding

Effect of SiC and TiC content on microstructure and wear behavior of Ni-based composite coating manufactured by laser cladding on Ti-6Al-4V

Microstructure, oxidation resistance and mechanical properties of stellite 12 composite coating doped with submicron TiC/B4C by laser cladding

Microstructural and Performance Analysis of (TiAl)95−xCu5Nix Coatings Prepared via Laser Surface Cladding on Ti–6Al–4V Substrates

Effect of TiC content on microstructure and properties of TiC/Ni60 coatings on Ti6Al4V alloy deposited by laser cladding

Effects of TiC on the Microstructure and Mechanical Properties of Four Fe-Based Laser Cladding Coatings

Microstructure and Erosion Wear of In Situ TiC-Reinforced Co-Cr-W-C (Stellite 6) Laser-Cladded Coatings

Effect of TiC addition on the microstructure and properties of Ni3Ta–TaC reinforced Ni-based wear-resistant coating

Optimization and high-temperature wear characterization of Stellite alloy claddings developed using TIG welding on 56NiCrMoV7 die steel

Influence of Ti on the Microstructure and Performance of Fe-Cr Alloy Cladding Layer

Study on the effect of TiC/B on the performance of laser cladding in-situ fabricating wear-resistant self-lubricating coatings

Design, fabrication, microstructure and properties of in-situ synthesized TiC reinforced stainless steel matrix composite coating by laser cladding

Study on the friction and wear performance of laser cladding WC-TiC/Ni60 coating on the working face of shield bobbing cutter

Stellite3-Ti3SiC2-Cu composite coatings on IN718 by laser cladding towards improved wear and oxidation resistance

Microstructure and high-temperature wear properties of in situ TiC composite coatings by plasma transferred arc surface alloying on gray cast iron

Effect of Y2O3 Content on Microstructure and Wear Resistance of Laser Cladding Layer of Stellite-6 Alloy

Laser Synthesis of Titanium Aluminides Matrix Composite Coatings Reinforced by In-Situ Titanium Carbide Particles on Ti-6Al-4V Substrate