Abstract:In order to solve the problem of shield hobbing cutter failure due to bias wear and chipping during tunnel boring, TiC-WC/Ni60 coating was prepared on the surface of H13 steel to improve the wear resistance of shield hobbing cutter. In this paper, four kinds of WC-TiC/Ni60 composite coatings with different content ratios of 5 wt% TiC+25 wt% WC, 10 wt% TiC+20 wt% WC, 15 wt% TiC+15 wt% WC and 20 wt% TiC+10 wt% WC were prepared on the surface of H13 steel by using the coaxial powder-feeding laser cladding equipment. The micromorphology, phase, hardness and friction and wear properties were fully studied. The results show that cross-sectional organization of the fused cladding layer mainly consists of columnar crystals, cytocrystals and equiaxial crystals; the hard phases in the fused cladding layer mainly consist of TiWC 2 , Cr 4 Ni 5 W, and Cr 3 C 2 , and so on; The microhardness of the cross-section of the fused cladding layer shows a trend of decreasing at first, then increasing and finally decreasing, and the highest hardness of the fused cladding layer occurs at the subsurface of the fused cladding layer; the friction coefficient of the fused cladding layer shows a trend of decreasing first and then increasing; the wear volume of the fused cladding layer is significantly lower than that of the substrate, and the wear volume of the 15 wt% TiC coating is the smallest of 1.313 mm 3 , which is 86.9 % lower than that of the substrate; the wear mechanism of the substrate is mainly abrasive wear and adhesive wear, and the wear mechanism of the fused cladding layer is mainly brittle spalling, abrasive wear and oxidative wear. The analysis of the experimental results shows that the surface properties of the coating are best when both TiC and WC contents are 15 wt%.

Effect of TiC addition on the microstructure and properties of Ni3Ta–TaC reinforced Ni-based wear-resistant coating

Microstructure and properties of Ta-reinforced NiCuBSi + WC composite coating deposited on 5Cr5MoSiV1 steel substrate by laser cladding

Microstructure and properties of in-situ synthesized Ni3Ta-TaC reinforced Ni-based coatings by laser cladding

Effect of in-situ grown TiC on microstructure and tribological performance of laser cladded NiCrAl-40 %WC coating by addition of Ti

Influence of Carbon Contents on the Structure and Tribocorrosion Properties of Tisicn Coatings on Ti6al4v

Microstructure and Wear Resistance of In Situ Synthesized Ti(C, N) Ceramic-Reinforced Nickel-Based Coatings by Laser Cladding

Effect of TiC addition on the microstructure and properties of laser cladding Ni60A coatings on H13 steel surface

Evolution of microstructure and wear mechanism in laser clad Al0.5CoCrFeNiSi0.5Tix coatings in response to the Ti addition

Microstructure and tribological properties of laser cladded TiC reinforced WC-10Co4Cr coatings at 500 °C

Microstructure and properties of TiC-enhanced CrMnFeCoNi high-entropy alloy coatings prepared by laser cladding

Influence of Ti element on the microstructure and crack of modulated WC-strengthened Ni-based alloy coatings by laser cladding

In Situ Synthesis of (M:Nb,Ta)C/Ni35 Composite Coating Cladded on 40Cr Steel

Friction and wear behavior of Ni-based alloy coatings with different amount of WC–TiC ceramic particles

Study on the friction and wear performance of laser cladding WC-TiC/Ni60 coating on the working face of shield bobbing cutter

Effect of WC addition on microstructure and properties of laser melting deposited Ti6Al4V

Microstructure and wear resistance of Ni-based tungsten carbide coating by laser cladding on tunnel boring machine cutter ring

Effect of SiC and TiC content on microstructure and wear behavior of Ni-based composite coating manufactured by laser cladding on Ti-6Al-4V

Effect of Ti3SiC2 addition on microstructure and tribological property of laser cladded NiCrAl–WC–Ti3SiC2 composite coatings at 500 °C

Effect of Mo addition on microstructure and wear resistance of laser clad AlCoCrFeNi-TiC composite coatings

Microstructural and Performance Analysis of (TiAl)95−xCu5Nix Coatings Prepared via Laser Surface Cladding on Ti–6Al–4V Substrates

Microstructural evolution, mechanical properties and wear behavior of in-situ TiC-reinforced Ti matrix composite coating by induction cladding