Abstract:In this work, the structural and mechanical properties of ternary Mo-Al-N alloys are investigated by combining thin film growth experiments and density functional theory (DFT) calculations. Mo1−xAlxNy thin films (∼300 nm thick), with various Al fractions ranging from x = 0 to 0.5 and nitrogen-to-metal (Al + Mo) ratio ranging from y = 0.78 to 1.38, were deposited by direct-current reactive magnetron cosputtering technique from elemental Mo and Al targets under Ar + N2 plasma discharges. The Al content was varied by changing the respective Mo and Al target powers, at a fixed N2 (20 SCCM) and Ar (25 SCCM) flow rate, and using two different substrate temperatures Ts = 350 and 500 °C. The elemental composition, mass density, crystal structure, residual stress state, and intrinsic (growth) stress were examined by wavelength dispersive x-ray spectroscopy, x-ray reflectivity, x-ray diffraction, including pole figure and <math> si n 2 ψ</math> measurements, and real-time in situ wafer curvature. Nanoindentation tests were carried out to determine film hardness H and elastic modulus EIT, while the shear elastic constant C44 was measured selectively by surface Brillouin light spectroscopy. All deposited Mo1−xAlxNy films have a cubic rock-salt crystal structure and exhibit a fiber-texture with a [001] preferred orientation. The incorporation of Al is accompanied by a rise in nitrogen content from 44 to 58 at. %, resulting in a significant increase (2%) in the lattice parameter when x increases from 0 to 0.27. This trend is opposite to what DFT calculations predict for cubic defect-free stoichiometric Mo1−xAlxN compounds and is attributed to variation in point defect concentration (nitrogen and metal vacancies) when Al substitutes for Mo. Increasing Ts from 350 to 500 °C has a minimal effect on the structural properties and phase composition of the ternary alloys but concurs to an appreciable reduction of the compressive stress from −5 to −4 GPa. A continuous increase and decrease in transverse sound velocity and mass density, respectively, lead to a moderate stiffening of the shear elastic constant from 130 to 144 GPa with increasing Al fraction up to x = 0.50, and a complex and nonmonotonous variation of H and EIT is observed. The maximum hardness of ∼33 GPa is found for the Mo0.81Al0.19N1.13 film, with nitrogen content close to the stoichiometric composition. The experimental findings are explained based on structural and elastic constant values computed from DFT for defect-free and metal- or nitrogen-deficient rock-salt MoAlN compounds.

Anomalous effect of nitrogen flow ratio on mechanical properties of NbMoTaW:(N,O) medium entropy alloy films

Effects of Nitrogen Flow Ratio on the Structure and Properties of Reactively Sputtered (almonbsitativzr)n(x) Coatings

Effects of nitrogen content on microstructures and mechanical properties of (AlCrTiZrHf)N high-entropy alloy nitride films

Effects of N element on the micro-structures and properties of (TiAlMoNbW)N high entropy nitride film

Microstructure evolution and mechanical properties of refractory high-entropy alloy nitride film

Mechanical properties and oxidation behavior of NbMoTaW x refractory high entropy alloys

Mechanical and Tribological Properties of Laminated (NbTaMoW)Nx Films

Evolutions of the Microstructure and Properties of the (CrMoNbTaZr)NX Films Prepared by Reactive Magnetron Sputtering: Effects of Stoichiometry and Crystallinity

Structure, stress, and mechanical properties of Mo-Al-N thin films deposited by dc reactive magnetron cosputtering: Role of point defects

Effect of W/Mo ratio on the as-cast microstructure of Nb-modified Hastelloy N alloys

Influence of Oxygen and Nitrogen Flow Ratios on the Microstructure Evolution in AlCrTaTiZr High-Entropy Oxynitride Films

Weak enthalpy-interaction-element-modulated NbMoTaW high-entropy alloy thin films

Microstructure and mechanical properties of (AlCrTiZrV)Nx high-entropy alloy nitride films by reactive magnetron sputtering

Effect of Mechanical Alloying and Sintering Behavior on the Microstructure and Properties of NbMoTaWRe Refractory High Entropy Alloy

Structural and Mechanical Properties of Multi-Element (alcrmotatizr)nx Coatings by Reactive Magnetron Sputtering

Phase, mechanical property and corrosion resistance evaluation of W-Nb-Ta-Ti and W-Nb-Ta-Ti-N medium entropy alloy thin films

The effect of molybdenum content on microstructure, mechanical, tribological and corrosion behavior of Zr-Mo-N composite films

Microstructure, mechanical and tribological properties of NbMoWTaAg refractory high entropy films with nano-layered self-organization

Effect of Mo on the morphology, microstructure and mechanical properties of NbTa 0.5 TiMo x refractory high entropy alloy fabricated by laser powder bed fusion using elemental mixed powders

Mechanical performance of (NbTaW)1−xMox (x = 0, 0.05, 0.15, 0.25) refractory high entropy alloys: Perspective from experiments and first principles calculations

Study on the microstructural evolution in NbMoTaW series refractory multi-principal element alloy films by low-energy and high-flux He ions irradiation