Abstract:Continuous silicon carbide fiber–reinforced silicon carbide matrix (SiCf/SiC) composites have developed into a promising candidate for structural materials for high–temperature applications in aerospace engine systems. This is due to their advantageous properties, such as low density, high hardness and strength, and excellent high temperature and oxidation resistance. In this study, SiCf/SiC composites were fabricated via polymer infiltration and pyrolysis (PIP) with the lower–oxygen–content KD–II SiC fiber as the reinforcement; a mixture of 2,4,6,8–tetravinyl–2,4,6,8–tetramethylcyclotetrasiloxane (V4) and liquid polycarbosilane (LPCS), known as LPVCS, was used as the precursor; while pyrolytic carbon (PyC) was used as the interface. The effects of oxidation treatment at different temperatures on morphology, structure, composition, and mechanical properties of the KD–II SiC fibers, SiC matrix from LPVCS precursor conversion, and SiCf/SiC composites were comprehensively investigated. The results revealed that the oxidation treatment greatly impacted the mechanical properties of the SiC fiber, thereby significantly influencing the mechanical properties of the SiCf/SiC composite. After oxidation at 1300°C for 1h, the strength retention rates of the fiber and composite were 41% and 49%, respectively. In terms of the phase structure, oxidation treatment had little effect on the SiC fiber, while greatly influencing the SiC matrix. A weak peak corresponding to silica (SiO2) appeared after high–temperature treatment of the fiber; however, oxidation treatment of the matrix led to the appearance of a very strong diffraction peak that corresponds to SiO2. The analysis of the morphology and composition indicated cracking of the fiber surface after oxidation treatment, which was increasingly obvious with the increase in the oxidation treatment temperature. The elemental composition of the fiber surface changed significantly, with drastically decreased carbon element content and sharply increased oxygen element content.

Enhanced strength and thermal oxidation resistance of shaddock peel-polycarbosilane-derived C–SiC–SiO2 composites

Microstructural Regulation, Oxidation Resistance and Mechanical Properties of Cf/SiC/SiHfBOC Composites Prepared by Chemical Vapor Infiltration with Precursor Infiltration Pyrolysis

Improvement of Strength and Oxidation Resistance for SiC/graphite Composites by SiC Coating

Enhanced strength and toughness of SiC/C composite ceramics via SiC@graphene core–shell nanoparticles

Oxidation Kinetics and Its Impact on the Strength of Carbon Short Fiber Reinforced C/SiC Ceramics

Characterization of hot-pressed short carbon fiber reinforced ZrB2–SiC ultra-high temperature ceramic composites

Preparation and Properties of SiOC Ceramic Modified Carbon Fiber Needled Felt Preform Composites

Effect of Oxidation Treatment on KD–II SiC Fiber–reinforced SiC Composites

Mechanical and ablation properties of 3D orthogonal woven C/C-SiC composite based on high-solid-loading slurry impregnation

Improving thermal conductivity of Al/SiC composites by post-oxidization of reaction-bonded silicon carbide preforms

Preparation and Characterization of An All Oxide Ceramic Matrix Composite by A Novel Method

In-situ SiC nanowires reinforced SiC-based multicomponent ceramic coating for protecting SiOC/CF composites

Fabrication and properties of three-directional orthogonal aluminosilicate fiber fabric-reinforced mullite composite

Direct Ink Writing of Chopped Carbon Fibers Reinforced Polymer-derived SiC Composites with Low shrinkage and High Strength

Improved Mechanical Properties of Al2O3-25 Vol% SiCw Composites Prepared by Oscillatory Pressure Sintering

Fabrication and oxidation resistance of mullite/yttrium silicate multilayer coatings on C/SiC composites

Precursor Infiltration and Pyrolysis Cycle-Dependent Microwave Absorption and Mechanical Properties of Lightweight and Antioxidant Carbon Fiber Felts Reinforced Silicon Oxycarbide Composites.

Oxidation resistance of SiCf/SiC composites with a PyC/SiC multilayer interface at 500 °C to 1100°C

Microstructure and High-Temperature Oxidation Resistance of Ti-6Al-4V Alloy with In-Situ SiC-SiO2 Nano-Composite Coating by LPDS Technique

Processing and mechanical performance of 3D Cf/SiCN composites prepared by polymer impregnation and pyrolysis

High‐temperature behavior and self‐enhancing mechanisms of oxide‐bonded SiC porous ceramics