Abstract:Copper as well as copper base composites reinforced with coated and uncoated 1 wt% diamond, graphite particles or short carbon fibers are prepared by powder metallurgy process. The reinforcement particles were encapsulated with silver as well as copper layer by using the electroless deposition technique to investigate the influence of the reinforcement surface coating on the microstructure, density, electrical and thermal properties of the sintered samples. The coated and the uncoated powders were cold compacted at 600 MPa, and then sintered at 1173 K (900°C) for 2 h under hydrogen atmosphere. The phase composition, morphology and microstructure of the prepared powders as well as the copper base sintered composites were investigated using X-ray diffraction analysis (XRD) and Scanning Electron Microscope (SEM) equipped with an Energy Dispersive Spectrometer (EDS) respectively. The density of the sintered composites was measured by Archimedes method. The copper base consolidated composites had a density up to 96% and the reinforcement coated particles were distributed uniformly within the copper matrix better than the uncoated one. The electrical resistivity at room temperature and the heat transfer conduction of the produced samples were measured in a temperature range between 323 K (50°C) and 393 K (120°C). The results observed that the sintered materials prepared from the coated powder have lower electrical resistivity than the sintered materials prepared from the mixed powders. On the other hand the thermal conductivity values were calculated using the heat transfer conduction values by means of the Fourier formula. The results observed that the thermal conductivity of copper is (391 W/m·K), 1 wt% diamond/Cu is (408 W/m·K), 1 wt% graphite coated silver/Cu is (393 W/m·K), 1 wt% Cu coated short carbon fiber/Cu is (393 W/m·K), graphite/Cu is (383 W/m·K) and short carbon fiber/Cu is (382 W/m·K). The obtained composites are expected to be suitable for heat sink applications. The heat transfer testing experiments were done. The forced convection of the present work was done and compared with the previous work in the literature, and satisfactory agreement was achieved.

Copper–micrometer-sized diamond nanostructured composites

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

Enhanced Interfacial Bonding in Copper/Diamond Composites via Deposition of Nano-copper on Diamond Particles

Tribological, mechanical and thermal response of diamond micro-particles reinforced copper matrix composites fabricated by powder metallurgy

Scalable monolayer-functionalized nanointerface for thermal conductivity enhancement in copper/diamond composite

Microstructure of Cu-diamond Composites with Near-Perfect Interfaces Prepared Via Electroplating and Its Thermal Properties

Reinforcing Copper Matrix Composites Through Molecular-Level Mixing of Functionalized Nanodiamond by Co-Deposition Route

Micro Heat Sink Structure with High Thermal Conductive Composite Via Micromachining Process

Synergetic effect enabling high thermal conductivity in Cu/diamond composite

Structure and properties of composite materials based on copper strengthened with diamond nanoparticles by mechanical alloying

Fabrication of diamond/copper composite thin plate based on a single-layer close packed diamond particles network for heat dissipation

Development of High Thermal Conductivity Copper Alloys with Diamond Particle Additions

Rapid Manufacturing of Diamond/Cu Composites Prepared Via Ultrasonic Consolidation

Fabrication of Titanium and Copper-Coated Diamond/Copper Composites via Selective Laser Melting

Copper Matrix Composites Reinforced with Nanometer Alumina Particle

Microstructure and Interface Evolution of Diamond/cu Composites Prepared Via Ultrasonic Additive Manufacturing (UAM)

Progress in Interface Modification and Nanoscale Study of Diamond/Cu Composites

Critical effect and enhanced thermal conductivity of Cu-diamond composites reinforced with various diamond prepared by composite electroplating

Fabrication, Microstructure, Thermal and Electrical Properties of Copper Heat Sink Composites

Net-shape forming process for diamond-copper composites with high thermal conductivity

Quantitative control of interfacial structure and thermal conductivity between diamond and copper via thermal diffusion of alloying element