Abstract:We report a solid strategy to realize heteroface mono‐Si wafers for PERC‐SE solar cells, by employing alkaline polishing for the rear and well‐established MCCE etching to form honeycomb texture for the front in one wet process successively. It can double the throughput of existing texturing processes and reduce the etching wastewater. Passivated emitter and rear cell (PERC) with laser‐doped selective emitter (SE) has become mainstream in the PV industry. In this work, we report a solid strategy to realize heteroface monocrystalline silicon (mono‐Si) wafers for PERC‐SE solar cells by employing alkaline polishing to form a polished surface for the rear side and well‐established metal‐catalyzed chemical etching to form a honeycomb texture for the front side in one wet process successively. The key to success lies in the fact that the two back‐to‐back wafers inserted into one slot in the cassette are tightly attached together in MCCE etching so that only the exposed surfaces are etched to form textures, while the rear polished surfaces are still retained to avoid wrap‐around etching. With the strategy, the mono‐Si PERC‐SE solar cells achieve an average efficiency of over 22.0%, no poorer than that of the reference system (traditional alkaline texturing and rear acidic polishing), and have good light trapping capability for oblique incident light. Moreover, the total Si removal in the novel process is only ~0.4 g, which is far less than that in the traditional process. More importantly, the strategy can also double the throughput of existing texturing processes and significantly reduce the amount of etching waste. Therefore, the work is expected to provide a promising way to mass produce efficient mono‐Si PERC‐SE solar cells with a superior rear surface, achieved without increasing the number of processing steps, and lower cost.

Suppressing The Blistering of Silicon Nitride in PERC Solar Cells for High Industrial Yield

Influence of Al2O3/SiNx Rear-Side Stacked Passivation on the Performance of Polycrystalline PERC Solar Cells

Improved Al 2 O 3 / SiN x and SiO 2 / SiN x stack passivation layer structure PERC sc‐silicon solar cells on mass production line

Tuning Back Side Passivation for Enhancing the Performance of PERC Solar Cells

Preventing the Formation of Voids in the Rear Local Contact Areas for Industrial-Type PERC Solar Cells

Industrail Technology of Passivated Emitter and Rear Cells with Silicon Oxynitride and Silicon Nitride As Rear Passivation for High Efficiency BIPV Modules

Application of SiO2 Passivation Technique in Mass Production of Silicon Solar Cells

Effective Way to Reduce Rear-Side Potential-Induced Degradation of Bifacial PERC Solar Cells

Optimization of Rear-Side Passivation for Enhancing the Performance of Bifacial PERC+ Solar Cells

Passivated Emitter and Rear Cell Silicon Solar Cells with a Front Polysilicon Passivating Contacted Selective Emitter

Bi-layer in-situ phosphorus doped poly-Si films by PECVD for blistering-free high-efficiency industrial TOPCon solar cells

Industrial Applications Of A Novel Technology For Commercial Multicrystalline Silicon Solar Cells

Optimization of Controllable Factors in the Aluminum Silicon Eutectic Paste and Rear Silicon Nitride Mono-Passivation Layer of PERC Solar Cells

Compensating Cutting Losses by Passivation Solution for Industry Upgradation of TOPCon and SHJ Solar Cells

Performance of Large Area n-TOPCon Solar Cells with Selective Poly-Si Based Passivating Contacts Prepared by PECVD Method

A solid strategy to realize heteroface selective emitter and rear passivated silicon solar cells

High-Efficiency Silicon Inverted Pyramid-Based Passivated Emitter and Rear Cells

Investigation on the passivated Si/Al2O3 interface fabricated by non-vacuum spatial atomic layer deposition system

Light management of PERC solar cell with the front and back dielectric multilayers

Enhancing industrialization TOPCon solar cell efficiency via comprehensive anti-reflection passivation film optimization

Numerical study of mono-crystalline silicon solar cells with passivated emitter and rear contact configuration for the efficiency beyond 24% based on mass production technology