Abstract:A shaping test of CuSn10 powders was carried out by using the selective laser melting (SLM) technology to study influences of process parameters of SLM on compactness of specimens. Meanwhile, process parameters were optimized based on the response surface methodology. Meanwhile, phase composition and microstructure of formed part were analyzed by XRD and OM. Results demonstrated that as the energy density of laser body increases from 146.7 J·mm -3 to 181.3 J·mm -3 , pores of samples decrease and the compactness increases from 98.97% to about 99.7%. Subsequently, the compactness begins to decrease with the continuous increase of laser energy density. The incomplete melting of powder under low energy density and gasification of powders under high energy density are major factors that influence the compactness. Over low or high laser energy density is disadvantageous for the improvement of compactness. A mathematical model of interaction between three factors (laser power, laser scanning speed and scanning space) and response value (compactness) was built up by using the BBD principle design test of response surface methodology. The degree of fitting (R 2 ) and correction coefficient (R 2 adj ) of the model were 0.9952 and 0.9866, which agree well with the fitting degree of experimental tests. Among three factors, influences of laser power and scanning speed on compactness are equivalent and more significant than scanning space. The optimal process parameters which were predicted by the model were laser power=331.471 W, scanning speed=648.045 mm·s -1 , scanning space=69.9302 μm. Under this circumstance, the compactness of CuSn10 powders after SLM is 99.75%. According to experimental verification, the practical value of compactness is 99.74%, showing a very small relative error. This proves that the BBD model is reliable. The shaped part is mainly composed of α-Cu phase and metastable phase β'-Cu13.7Sn. Compared with the original powders, the content of metastable phase β' increases significantly, while the δ-Cu41Sn11 phase disappears.

Process optimization of micro selective laser melting and comparison of different laser diameter for forming different powder

Effect of Processing Parameters on Forming Defects During Selective Laser Melting of AlSi10Mg Powder

Process parameter optimization and mechanical properties for selective laser melting of AlSi10Mg alloy

Experimental study on parameters optimization of selective laser melting 316L stainless steel based on response surface methodology

Investigation into the effect of process parameters on density, surface roughness, and mechanical properties of 316L stainless steel fabricated by selective laser melting

Simulation and experimental studies on process parameters, microstructure and mechanical properties of selective laser melting of stainless steel 316L

Effects of the processing parameters on the forming quality of stainless steel parts by Selective Laser Melting

Coupling Analysis on Microstructure and Residual Stress in Selective Laser Melting (SLM) with Varying Key Process Parameters

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

Effect of layer-by-layer laser remelting process on the microstructure and performance of selective laser melting 316L stainless steel

Process Optimization and Mechanical Property Evolution of AlSiMg0.75 by Selective Laser Melting

System Development, Formability Quality and Microstructure Evolution of Selective Laser-Melted Magnesium

Investigation into the effect of process parameters on microstructural and physical properties of 316L stainless steel parts by selective laser melting

Process Parameter Optimization on Selective Laser Melting of CuSn10 Powders Based on Response Surface Methodology

Study on performance optimization of 316L stainless steel parts by High-Efficiency Selective Laser Melting

Study on the Technique During Selective Laser Melting of Stainless Steel Powder

The Process Research of 316L Stainless Steel in Selective Laser Melting

Effects of Powder Characteristics on Selective Laser Melting of 316l Stainless Steel Powder

Influence of Laser Process on the Porosity-Related Defects, Microstructure and Mechanical Properties for Selective Laser Melted AlSi10Mg Alloy

Optimization of Processing Parameters and Establishment of a Relationship Between Microstructure and Mechanical Properties of SLM Titanium Alloy

Surface Characteristics Enhancement and Morphology Evolution of Selective-Laser-melting (SLM) Fabricated Stainless Steel 316L by Laser Polishing