Abstract:Selective Laser Melting (SLM) additive manufacturing (AM) is recognized for its rapid production capabilities, energy efficiency, reduced environmental impact, and design flexibility. It has shown promising applications in architecture and civil infrastructure. However, before applying this technology to the actual production of building structures, it is necessary to develop corresponding constitutive models to predict the material behaviour accurately. Previous studies on the mechanical properties of SLM 316 L stainless steel (SS) have not been comprehensive enough, particularly regarding the mechanical properties after exposure to elevated temperatures. This paper explores the effects of build orientation (X, Y, and Z construction orientations), layer thickness (2 mm, 4 mm and 6 mm), and thermal treatment (20 degrees C, degrees C, 300 degrees C, 600 degrees C, and 900 degrees C) on the mechanical properties of SLM-produced 316 L SS plates. Monotonic tensile tests and scanning electron microscopy (SEM) are employed to evaluate the mechanical characteristics and microstructure of the plates. Results indicate that the mechanical properties vary with manufacturing direction and material thickness. Specifically, properties are enhanced in the X and Y directions compared to the Z direction, and generally decline with increased material thickness except for elongation at fracture. Elevated temperature treatment has a significant effect on the mechanical properties of SLM 316 L SS. Thermal treatments at temperatures below 600 degrees C are found to increase yield and ultimate tensile strengths, whereas exposures at 900 degrees C decrease strength but increase ductility. The elastic modulus remains relatively unaffected by temperature changes. A reduction model is developed to assess the mechanical properties of SLM 316 L SS, introducing a new coefficient that predicts the variation in the elastic modulus, yield strength, ultimate tensile strength, elongation, strain hardening parameters, and Poisson's ratio before and after thermal exposure. This model has been calibrated to effectively represent the mechanical properties of SLM 316 L SS under different manufacturing conditions and provides a foundation for future research on other alloy systems and heat treatment protocols.

Experimental Characterization and Strengthening Mechanism of Process-Structure-property of Selective Laser Melted 316 L

Experimental Characterization and Yield Strength Model for Process-Structure-Property of Selective Laser Melted 316L

Deformation Mechanisms of Selective Laser Melted 316l Austenitic Stainless Steel in High Temperature Low Cycle Fatigue

Compressive Mechanical Response and Microstructures in Low Strain Rate Plastic Deformation of Stainless Steel 316l Fabricated by Selective Laser Melting

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Process-structure-property Modeling for Postbuild Heat Treatment of Powder Bed Fusion Ti-6Al-4V

Regulation of Microstructure, Residual Stress, and Mechanical Properties by Pre-straining and Subsequent Heat Treatment in Selective Laser Melted 304L Stainless Steel

Analysis of Fatigue Properties of Selective Laser Melting 316L Stainless Workpiece After Post-heat Treatment

Effect of Heat Treatment on Microstructural Evolution in Additively Manufactured 316L Stainless Steel

Effect of Heat Treatment on Microstructures and Mechanical Properties of SS316L by Micro Selective Laser Melting

Mechanical Properties and Corrosion Behavior of Selective Laser Melted 316L Stainless Steel after Different Heat Treatment Processes

Mechanical Properties of SLM 316L Stainless Steel Plate Before and after Exposure to Elevated Temperature

Influence of Post Heat Treatment on Microstructure and Mechanical Property of Ti6Al4V Parts Produced by Selective Laser Melting

Effect of Post-Heat Treatment on Residual Stress and Tensile Strength of Hybrid Additive and Subtractive Manufacturing

Microstructure, mechanical properties, and deformation behaviour of LPBF 316L via post-heat treatment

Enhanced Strength-Ductility Synergy Properties in Selective Laser Melted 316L Stainless Steel by Strengthening Grinding Process

Strengthening Mechanisms in Selective Laser Melted 316L Stainless Steel

Effect of heat treatment on the tensile behavior of selective laser melted Ti-6Al-4V by in situ X-ray characterization

Evolution of Cyclic Thermal Stress in Selective Laser Melting of 316L Stainless Steel: a Realistic Numerical Study with Experimental Verification

Influence of Modified Microstructures and Characterized Defects on Tensile Properties and Anisotropy of Selective Laser Melting-Produced Ti6Al4V Alloys

Effects of Defects and Microstructures on Tensile Properties of Selective Laser Melted Ti6Al4V Alloys Fabricated in the Optimal Process Zone