Abstract:Plastic deformation of low/high density polyethylene (LDPE/HDPE) was analyzed in this work using positron annihilation lifetime spectroscopy (PALS). It was shown that in undeformed LDPE, both the mean ortho-positronium lifetime (τ3) and its dispersion (σ3), corresponding to the average size and size distribution of the free-volume pores of the amorphous component, respectively, were clearly higher than in HDPE. This effect was induced by a lower and less uniform molecular packing of the amorphous regions in LDPE. During the deformation of LDPE, an increase in the τ3 value was observed within the local strains of 0–0.25. This effect was mainly stimulated by a positive relative increase in interlamellar distances due to the deformation of lamellar crystals oriented perpendicular (increased by 31.8%) and parallel (decreased by 10.1%) to the deformation directions. At the same time, the dimension of free-volume pores became more uniform, which was manifested by a decrease in the σ3 value. No significant effect of temperature or strain rate on the τ3 and σ3 values was observed during LDPE deformation. In turn, in the case of HDPE, with an increase in the strain rate/or a decrease in temperature, an intensification of the cavitation phenomenon could be observed with a simultaneous decrease in the τ3 value. This effect was caused by the lack of annihilation of ortho-positonium (o-Ps) along the longer axis of the highly anisotropic/ellipsoidal cavities. Therefore, this dimension was not detectable by the PALS technique. At the same time, the increase in the dimension of the shorter axis of the cavities was effectively limited by the thickness of amorphous layers. As the strain rate increased or the temperature decreased, the σ3 value during HDPE deformation increased. This change was correlated with the initiation and intensification of the cavitation phenomenon. Based on the mechanical response of samples with a similar yield stress, it was also proven that the susceptibility of the amorphous regions of LDPE to the formation of cavities is lower than in the case of amorphous component of HDPE.

Impact testing of high-density polyethylene structure

High-strain Rate Compressive Behavior of Concrete with Two Different Substituted Recycled Plastic Aggregates: Experimental Characterization and Probabilistic Modeling

Experimental and theoretical study of stress relaxation in high-density polyethylene

The high strain-rate behaviour of three molecular weights of polyethylene examined with a magnesium alloy split-Hopkinson pressure bar

Low velocity impact behavior and simulation of parametric effect analysis for UHMWPE/LLDPE thermoplastic composite laminates

Semi-Crystalline Polymers Applied to Taylor Impact Test: Constitutive, Experimental and FEM Analysis

Statistical Mechanics of Kevlar® KM2® Plus Nanostructure: Deformations and High-Rate Impact

Experimental Study on Characterizing Damage Behavior of Thermoplastics

Image-Based Inertial Impact Test for Composite Interlaminar Tensile Properties

Multi-Scale Experimental Characterization for LS-DYNA MAT213 Modeling of Composite Structures under High Strain Rate

Molecular dynamics simulation of plastic deformation in polyethylene under uniaxial and biaxial tension

Numerical and Theoretical Modeling of the Elastic-Plastic Bulging Deformation of UHMWPE Composite Laminate under High-Speed Impact

Strain Rate and Temperature Influence on Micromechanisms of Plastic Deformation of Polyethylenes Investigated by Positron Annihilation Lifetime Spectroscopy

Impact response of thermoplastic composites – Experiments and modeling

Rate-dependent Constitutive Model of Poly(ethylene Terephthalate) for Dynamic Analysis

The behaviour of thermoplastic and thermoset carbon fibre composites subjected to low-velocity and high-velocity impact

Effects of high temperature and strain rate on the impact-induced inter-laminar shear behavior of plain woven CF/PEEK thermoplastic composites

A constitutive model of the compressive mechanical properties of ultra high molecular weight polyethylene (UHMWPE) at different temperatures and different strain rates

Modelling Fatigue Crack Growth in High-Density Polyethylene and Acrylonitrile Butadiene Styrene Polymers

Study On Constitutive Modeling For Large Deformation Behavior Of Polyethylene Considering Strain Rate Effect

Shock and spallation behavior of ultrahigh molecular weight polyethylene