Abstract:Plastic deformation of polyethylene in uniaxial and biaxial loading conditions is studied using molecular dynamics simulation. Effects of tensile strain rates from 1 × 10 5 to 1 × 10 9 s −1 , and mass density in the range of 0.923–0.926 g/cm 3 on mechanical behaviour and microstructure evolution are examined. Two biaxial tensile deformation modes are considered. One is through simultaneous stretching in both the x and y directions and the other sequential stretching, firstly in the x-direction and then in the y-direction while strain in the x-direction remains constant. Tangent modulus and yield stress that are determined using the stress–strain curves from the molecular dynamics simulation show a strong dependence on the deformation mode, strain rate and mass density, and all are in good agreement with results from the experimental testing, including fracture behaviour which is ductile at a low strain rate but brittle at a high strain rate. Furthermore, the study suggests that the stress–strain curves under uniaxial tension and simultaneous biaxial tension at a relatively low strain rate contain four distinguishable regions, for elastic, yield, strain softening and strain hardening, respectively, whereas under sequential biaxial tension, stress increases monotonically with the increase of strain, without noticeable yielding, strain softening or strain hardening behaviour. The molecular dynamics simulation also suggests that an increase in the strain rate enhances the possibility of cavitation. Under simultaneous biaxial tension, with the strain rate increasing from 1 × 10 6 to 1 × 10 9 s −1 , the molecular dynamics simulation shows that polyethylene failure changes from a local to a global phenomenon, accompanied by a decrease of the void size and increase of uniformity in the void distribution. Under sequential biaxial tension, on the other hand, the density of the cavities is clearly reduced.

Study On Constitutive Modeling For Large Deformation Behavior Of Polyethylene Considering Strain Rate Effect

Viscoelastic and Damage Model of Polyethylene Pipe Material for Slow Crack Growth Analysis

A Constitutive Model for Strain Hardening Behavior of Predeformed Amorphous Polymers: Incorporating Dissipative Dynamics of Molecular Orientation

Mechanical Behaviors of Copolymer Elastomers: Experimental Characterization and Constitutive Modelling

A study of elasticity deformation of polymethylene chain

Strain Rate-Dependent Hyperbolic Constitutive Model for Tensile Behavior of PE100 Pipe Material

Short-Term Mechanical Analysis of Polyethylene Pipe Reinforced by Winding Steel Wires Using Steel Wire Spiral Structural Finite Element Model

Rate-dependent Constitutive Model of Poly(ethylene Terephthalate) for Dynamic Analysis

Molecular dynamics simulation of plastic deformation in polyethylene under uniaxial and biaxial tension

Modeling the Rate-Dependent Ductile-Brittle Transition in Amorphous Polymers

Simulation and Analysis of the Loading, Relaxation, and Recovery Behavior of Polyethylene and Its Pipes

Compressive Properties and Constitutive Model of Semicrystalline Polyethylene.

Nonlinear Time-Dependent Mechanical Behavior of Medium-Density Polyethylene Pipe Material

Constitutive Modeling of Nonlinear Strain and Time Dependent Behaviors of Ballistic Gelatin at Low Strain Rates

Dynamic Tensile Behavior of Polyamide 6 at Different Strain Rates: Experiments and Constitutive Model

A viscoelastoplastic constitutive model of semi-crystalline polymers under dynamic compressive loading: Application to PE and PA66

Investigation of Tensile Creep Behavior for High-Density Polyethylene (HDPE) via Experiments and Mathematical Model

A phenomenological constitutive model for predicting both the moderate and large deformation behavior of elastomeric materials

Structure/property relationship of semi-crystalline polymer during tensile deformation: A molecular dynamics approach

Experimental Study of Yield Surface in Polypropylene Considering Rate Effect: Stress Path Dependence

Effect of deformation ratio of flow-induced crystallization on polyethylene in crystalline behavior, thermal stability, and tensile loading: a molecular dynamics simulation