Strain Rate-Dependent Hyperbolic Constitutive Model for Tensile Behavior of PE100 Pipe Material

Yan Li,Wenbo Luo,Maodong Li,Bo Yang,Xiu Liu

DOI: https://doi.org/10.3390/polym14071357

IF: 5

2022-03-27

Polymers

Abstract:It is not conservative to directly use the strength tested under the laboratory loading rates to evaluate the long-term creep strength of polymers. A suitable strain rate-dependent constitutive model is crucial for accurately predicting the long-term strength and mechanical behavior of polymer pressure pipes. In this study, the Kondner hyperbolic constitutive model is considered the base model in deriving the rate-dependent constitutive model for PE100 pipe material, and the yield stress and initial tangent modulus are the two rate-dependent parameters of the model. Uniaxial tension tests are carried out under five specified strain rates ranging from 10−5 s−1 to 5 × 10−2 s−1 to obtain these two parameters. It is demonstrated that the strain rate dependence of the yield stress and the initial tangent modulus can be described by either a power or a logarithm law. The predictions from the two models are in good agreement with the experiments. In contrast, the power-law rate-dependent Kondner model is more suitable for describing the rate-dependent tensile behavior of PE100 pipe material than the logarithm-law rate-dependent Kondner model, especially for the cases of very low strain rates which relate to the polymer pressure pipe applications.

polymer science

What problem does this paper attempt to address?

The problem that this paper attempts to solve is how to accurately predict the mechanical properties and strength of high - density polyethylene (HDPE) pressure pipe materials under long - term service conditions. Specifically, the author points out that it is not conservative to directly use the strength tested at the laboratory loading rate to evaluate the long - term creep strength of polymer materials, because the deformation rate in practical applications is much lower than the loading rate in laboratory tests. Therefore, establishing an appropriate strain - rate - dependent constitutive model is crucial for accurately predicting the long - term strength and mechanical behavior of HDPE pressure pipes.

To achieve this goal, the researchers adopted the Kondner hyperbolic constitutive model as the base model and derived a strain - rate - dependent constitutive model applicable to PE100 pipes. In this model, the yield stress \(\sigma_y\) and the initial tangent modulus \(E_0\) are two parameters related to the strain rate. By conducting uniaxial tensile tests in five specific strain - rate ranges (from \(10^{-5}\, \text{s}^{-1}\) to \(5\times 10^{-2}\, \text{s}^{-1}\)), the researchers obtained these parameters and found that the strain - rate dependence of the yield stress and the initial tangent modulus can be described by a power law or a logarithmic law.

The research results show that the power - law - dependent Kondner model is more suitable for describing the strain - rate - dependent tensile behavior of PE100 pipes than the logarithm - law - dependent Kondner model, especially under very low strain - rate conditions, which is relevant to the practical applications of polymer pressure pipes.

### Key Formulas
1. **Logarithmic Law**:
\[
\sigma_y = 34.62+3.18\log_{10}(\dot{\varepsilon})
\]
where \(\sigma_y\) is the yield stress and \(\dot{\varepsilon}\) is the strain rate.

2. **Power Law**:
\[
\sigma_y = 10.74 + 27.34\dot{\varepsilon}^{0.1}
\]

3. **Hyperbolic Constitutive Model**:
\[
\sigma_{\text{true}}=\frac{\varepsilon_{\text{true}}}{\frac{1}{E_0(\dot{\varepsilon})}+\frac{r}{\sigma_y(\dot{\varepsilon})}\varepsilon_{\text{true}}}
\]
where \(\sigma_{\text{true}}\) and \(\varepsilon_{\text{true}}\) are the true stress and the true strain respectively, \(E_0(\dot{\varepsilon})\) is the initial modulus, \(\sigma_y(\dot{\varepsilon})\) is the yield stress, and \(r\) is the ratio of the yield stress to the hypothetical ultimate stress.

4. **Yield Strain**:
\[
\varepsilon_y(\dot{\varepsilon})=\frac{\sigma_y(\dot{\varepsilon})}{(1 - r)E_0(\dot{\varepsilon})}
\]

By comparing these models with the experimental data, the researchers verified the validity of the models and proposed a more suitable strain - rate - dependent constitutive model for practical engineering applications.