Abstract:The structure, morphology, and mechanical properties of two compression-molded grades of ultrahigh-molecular-weight polyethylene (UHMWPE) and, for comparison, one conventional linear polyethylene (HDPE) were studied. Compression molding resulted in some preferred orientation of lamellae in the compression direction in UHMWPE samples, while no preferred orientation in HDPE. The mean crystal thickness estimated from the size distribution agrees better with those obtained from small-angle X-ray scattering (SAXS) and mechanical yield data than the thickness determined from the melting peak temperature. Microscopic examination of microtomed and etched UHMWPE samples showed that the lamellae are in the form of platelets with the width and length in the range of 300-700 nm. The lamellae radiate from primary nuclei forming small embryonal spherulites; their radial growth ends at 0.3-0.7 μm from the center. There is no evidence of branching and secondary nucleation from those primary lamellae. Because the lamellae are radially ordered, there is no parallel stacking of lamellae. Samples were subjected to deformation by plane-strain compression at a constant true strain rate. In axial UHMWPE samples, where lamellae were preferentially oriented along the loading direction, the second yield was clearly observed. The second yield was found to be related to the deformation instability leading to kinking of lamellae oriented initially along the loading direction. Kinking was clearly shown by SAXS and microscopic observation of microtomed and etched samples. No cooperativity of kinking was observed because the lamellae are arranged in small spherulites and not parallel in stacks. The stress-strain curves were fitted with model curves assuming crystal plasticity and network elasticity in the amorphous component. The effective density of the molecular network within the amorphous phase depended on the molecular weight of UHMWPE.

A constitutive model of the compressive mechanical properties of ultra high molecular weight polyethylene (UHMWPE) at different temperatures and different strain rates

Dynamic Constitutive Model of Ultra-High Molecular Weight Polyethylene (UHMWPE): Considering the Temperature and Strain Rate Effects.

Compressive Properties and Constitutive Model of Semicrystalline Polyethylene.

Temperature and Strain Rate Related Deformation Behavior of UHMWPE Fiber-Reinforced Composites

Temperature and strain rate effects on ultra‐high‐molecular‐weight‐polyethylene compression: An experimental and modeling approach

A Constitutive Model for Strain Hardening Behavior of Predeformed Amorphous Polymers: Incorporating Dissipative Dynamics of Molecular Orientation

Dynamic compressive behavior and constitutive model of polyamide-6 at different temperatures and strain rates

Statistical Dynamic Tensile Strength of Uhmwpe-Fibers

Molecular dynamics study of axial tensile response of crystalline ultra-high molecular weight polyethylene under different loading conditions

Morphology and Plastic Yielding of Ultrahigh Molecular Weight Polyethylene

Temperature-influenced cutting mechanism of UHMWPE fibres

Dynamic Tensile Behavior of Polyamide 6 at Different Strain Rates: Experiments and Constitutive Model

Shock and spallation behavior of ultrahigh molecular weight polyethylene

Influence of strain rate and temperature on mechanical properties of carbon woven-ply PPS thermoplastic laminates under dynamic compression

Effect of PEW and CS on the Thermal, Mechanical, and Shape Memory Properties of UHMWPE

Effects of high temperature and strain rate on the impact-induced inter-laminar shear behavior of plain woven CF/PEEK thermoplastic composites

The Out-of-Plane Compression Response of Woven Thermoplastic Composites: Effects of Strain Rates and Temperature

A viscoelastoplastic constitutive model of semi-crystalline polymers under dynamic compressive loading: Application to PE and PA66

Influence of molecular weight on molding efficiency and properties of sintered UHMWPE thick-size products

Compression properties and constitutive model of short glass fiber reinforced poly-ether-ether-ketone (PEEK)

Tensile Behavior of High-Density Polyethylene Including the Effects of Processing Technique, Thickness, Temperature, and Strain Rate