Abstract:Ni–SiC nano-composite coating, which simultaneously composed of both nanocrystalline consecutive Ni matrix and dispersed inert SiC nano-particles, has been fabricated by ultrasonic electroplating technique from a modified Watts bath containing SiC nano-particles. The influence of mechanical stirring and ultrasonication on the surface morphology of the nanocrystalline Ni–SiC nano-composite film has also been investigated. The surface morphology, microstructure, anti-corrosion property and electrocatalytic activity for hydrogen evolution of the obtained nanocrystalline Ni–SiC nano-composite film, are characterized using scanning electron microscopy (SEM) coupled with energy dispersive spectroscopy (EDS) system, atomic force microscopy (AFM), transmission electron microscope (TEM), X-ray diffraction (XRD) and electrochemical impedance spectroscopy (EIS) techniques. The results find that, mechanical stirring mainly prevents the sedimentation of the inert particles suspended in solutions, while ultrasonication mainly prevents the particles agglomeration. In the case of only mechanical stirring to disperse the SiC nano-particles, the composite surface is cauliflower alike. While in the case of both mechanical stirring and ultrasonication, the obtained Ni–SiC composite film is much smoother and composes of particles with the mean diameter of 42.9nm, and SiC particles are uniformly dispersed into Ni matrix. Meanwhile, the results obtained by polarization curves and EIS methods show that, when compared with the traditional polycrystalline Ni film, the obtained Ni–SiC nano-composite film exhibits the enhanced corrosion resistance in NaCl solutions, possesses much higher electrocatalytic activity for hydrogen evolution in KOH solutions.

Effects of Bath Composition, Current Density and Annealing Conditions on the Properties of the Electrodeposited Ni Seed Layer for Cu Contacts in Si Solar Cells

Microstructural evolution of wet deposited nickel interfacial phases on phosphorus doped silicon surface

Nickel Electroless Plating: Adhesion Analysis for Mono-Type Crystalline Silicon Solar Cells

Improvement of metal-semiconductor contact on silicon micro-structured surface by electroless nickel technique

Enhancing Adhesion and Reducing Ohmic Contact through Nickel–Silicon Alloy Seed Layer in Electroplating Ni/Cu/Ag

Influence of nickel silicide thin film on series resistance of silicon solar cells

Copper–Nickel Alloy Plating to Improve the Contact Resistivity of Metal Grid on Silicon Heterojunction Solar Cells

EFFECT OF ANNEALING ON THE CuInS2 THIN FILMS PREPARED BY CHEMICAL BATH DEPOSITION

Study of Annealing Effect Upon the Structural and Solar- Selective Properties of C/Ni/NiO Composite Coatings Prepared by Sol–gel Method

Effect of Annealing Ambient on the Thermal Stability of Cu/Zr42si9n49/Si Contact System

Electroplated Metallization Method For Crystalline Silicon Solar Cells

Effects of the Annealing Temperature on Ni Silicide/n-Si(100) Schottky Contacts

Atomic-scale silicidation of low resistivity Ni-Si system through in-situ TEM investigation

Formation of a Low Ohmic Contact Nickel Silicide Layer on Textured Silicon Wafers Using Electroless Nickel Plating

Copper-Plating Metallization With Alternative Seed Layers for c-Si Solar Cells Embedding Carrier-Selective Passivating Contacts

Influence Of Annealing Conditions On The Structure And Compositions Of Electrodeposited Cuinse2 Films

Ag and Sn capping layers for stabilizing Cu solar cell contacts against oxidation in air: effects of method and solution of deposition

Advancing nickel seed layer electroplating for enhanced contact and passivation performance in TOPCon solar cells

Electrodeposition and Characterization of Nano-Structured Ni–SiC Composite Films

Review of the Potential of the Ni/Cu Plating Technique for Crystalline Silicon Solar Cells

Influence of Nickel Film Thicknesses on Dark Current-Voltage Characteristics of Silicon Solar Cells