Abstract:This article presents a novel fully differential four-path passive mixer first receiver architecture, offering a wide radio frequency (RF) bandwidth and improved out-of-band (OOB) rejection. The design utilizes a current reuse approach in the process voltage temperature (PVT) resistant complementary transimpedance amplifier (TIA) to achieve excellent noise performance while minimizing power consumption. Besides, the integration of a second-order Twin-T Elliptic Low-pass Notch filter (TTE-LPNF) followed by the TIA enhances the linearity performance of the receiver and helps achieve wideband response due to positive capacitive feedback and shunting notch. The active RC-based buffer circuit is designed to efficiently drive a 50 $\Omega$ load impedance while providing substantial bandwidth. Moreover, the paper proposed a novel clock generator architecture based on a passive polyphase filter (PPF) and digital combinational logic that has reduced the required input local oscillator (LO) frequency by half compared to the conventional architecture for the same LO output, therefore, reducing the clock power. As a proof of concept, the proposed receiver is fabricated in TSMC 180 nm CMOS technology, and measurement is performed in the lab at room temperature. The receiver demonstrates an impressive RF bandwidth of 200 MHz while operating smoothly within the frequency range of 0.5 -2.5 GHz. The proposed mixer first receiver has achieved a conversion gain of 29 dB, a noise figure (NF) of 5.8 dB at the LO frequency of 1 GHz, and an out-of-band third-order intercept point (OOB-IIP3) of $+$ 18.5 dBm with power dissipation of 27 mW in signal path and 34 mW in clock path while operating at 1.8 V.

A 0.5–2.5 GHz Mixer First Receiver With 200 MHz RF Bandwidth and $+$18.5 dBm OB-IIP3 in 180 nm CMOS for 5G NR Band

A 0.1-1.9Ghz 65nm CMOS Variable-Gain Mixer-First Receiver with DSA and Noise-Shaping TIA.

A 0.5-8Ghz Reconfigurable CMOS RF Receiver Front-end for CR and DPA Applications

A 60–90 GHz Mixer-First Receiver with Adaptive Temperature-Compensation Technique

Design of a Low Power 60ghz OOK Receiver in 65nm CMOS Technology

A Sub-1-GHz Band High-Dynamic-Range Receiver with Integrated Self-Adaptive Multipart AGC Loops

A 27 - 57 GHz Down-conversion Mixer with Bulk Injection Technique

A C-Band Four-Channel Receiver with Current-Sharing and Large-Signal Multigated-Transistor Techniques in 65-Nm CMOS

A 5 GHz low power 0.18μm CMOS Gilbert cell mixer

A 2.1–2.5 GHz high linearity and low noise down-conversion active mixer

A Baseband-Noise-Cancelling Mixer-First CMOS Receiver Frontend Attaining 220 MHz IF Bandwidth With Positive-Capacitive-Feedback TIA

A 10ghz 2.8db Gain Passive Mixer In 0.18um Cmos Technology

A 43–97-GHz Mixer-First Front-End With Quadrature Input Matching and On-Chip Image Rejection

A Reusable Superheterodyne Dual-Band Down-Conversion Mixer With Hybrid Linearity-Enhanced Technique for 5G Non-Contiguous Multiband NR

A 24-to-30 GHz Ultra-High-Linearity Down-Conversion Mixer for 5G Applications Using a New Linearization Method

A 24‐ghz Active Up/down Bidirectional Mixer in 130‐nm RF CMOS

Design of Ultra-Low-Power 60-Ghz Direct-Conversion Receivers in 65-Nm CMOS

A Hybrid Coupler-First 5ghz Noise-Cancelling Dual-Mode Receiver with +10dbm In-Band IIP3 in Current-Mode and 1.7db NF in Voltage-Mode.

A LOW POWER, HIGH-LINEARITY CMOS DOWNCONVERSION FOLDED MIXER FOR 2.4GHz ISM BAND APPLICATIONS

A+21.2 Dbm Out-Of-Band Iip3 0.2-3ghz Rf Front-End Using Impedance Translation Technique

A 0.13&#x03bc;m CMOS UWB Receiver Front-End Using Passive Mixer